2N6292 is a PNP power transistor. In a PNP transistor, N represents the negative electrode, P represents the positive electrode, and the P-type transistor means that the positive electrode is the dominant carrier. The chip material of 2N6292 is silicon, and the packaging form is TO-220. Under the extreme operating voltage, its maximum allowable current value is 7A, and its maximum operating frequency is greater than 4MHZ.

 

Ⅰ.Specification parameters of 2N6292

•Configuration:Single
•Transistor polarity:NPN
•Pd-Power dissipation:40 W
•Frequency-jump:4MHz
•Power-Max:40 W
•Polarity:NPN
•Installation style:Through Hole
•Package/Box:TO-220-3
•Height:9.28 mm
•Length:10.28 mm
•Width:4.82 mm
•Minimum operating temperature:-65℃
•Maximum operating temperature:+150℃
•Collector continuous current:7 A
•Gain bandwidth product fT:4 MHz
•Maximum DC collector current:7 A
•Collector-emitter saturation voltage:3.5 V
•Collector-base voltage VCBO:80 V
•Maximum current amplification (hFE):150
•Emitter-base voltage VEBO:5 V
•Product type:BJTs-Bipolar Transistors
•DC collector/Base Gain hfe Min:30
•Minimum current amplification (hFE):30@2A, 4V
•Collector-emitter maximum voltage VCEO:70 V
•Product Category:Bipolar Transistor-Bipolar Junction Transistor (BJT)

 

Ⅱ.2N6292 commonly used application circuits

1.Audio amplifier: 2N6292 transistor is often used in audio amplifier circuits to drive speakers or other audio output devices. In the audio amplifier circuit, 2N6292 can be used as an amplifier tube to amplify weak audio signals and then drive the speaker to produce sufficient sound. Because the 2N6292 has high current and voltage capabilities, it can provide enough power to drive larger speakers and achieve good sound effects.

2.Motor drive: In some applications that need to control the speed and direction of the motor, 2N6292 can be used as the motor drive tube. By controlling the on and off states of 2N6292, the power on and off of the motor can be controlled, thereby realizing the start, stop, forward rotation, reverse rotation and other operations of the motor. At the same time, by adjusting the input signal of 2N6292, the speed and direction of the motor can be controlled.

3.Power switch: In the switching power supply, 2N6292 can be used as a power switch to control the on-off state of the power supply. By adjusting the on and off times of 2N6292, the output voltage and current of the power supply can be controlled, thereby achieving voltage and current stabilization of the power supply.

4.General switching applications: The PNP power transistor properties of 2N6292 make it suitable for general switching applications. As a switching tube, 2N6292 can realize on-off control of the circuit by controlling its on and off states. In power switches and other control circuits, the switching function of 2N6292 can be used to realize functions such as automatic control of the circuit, signal transmission, and equipment protection.

5.LED driver: By adjusting the on and off states of 2N6292, the power on and off of the LED can be controlled, thereby realizing the on and off control of the LED. At the same time, by adjusting the input signal of 2N6292, the brightness of the LED can be adjusted. In the LED drive circuit, you need to pay attention to the rated voltage and current of the LED, and select the appropriate drive circuit and control method to ensure the safe and stable operation of the LED.

6.DC-DC Converter: DC-DC converter is a circuit that converts DC power into different voltages or currents. In the output stage of the DC-DC converter, 2N6292 can be used as a switching tube by adjusting its conduction and Cut-off state, controls the output voltage and current of the power supply. By adjusting the input signal of 2N6292, the voltage and current of the power supply can be stabilized. In practical applications, attention needs to be paid to selecting appropriate drive circuits and control methods, as well as heat dissipation and protection measures to ensure the safe and stable operation of the DC-DC converter.

7.High-power drive: In some occasions that require high-power drive, such as electronic door locks, electric curtains, etc., 2N6292 can be used as a drive tube to provide sufficient drive current and voltage.

8.Motor drive: In some motor drive circuits, 2N6292 can be used as a motor drive tube to control the start and stop of the motor.

9.Power circuit: In some power circuits, 2N6292 can be used as a power switch or power adjustment tube to control the power on and off or adjust the power voltage.

Ⅲ.2N6292 Pin Configuration

 

Pin1:Base
Pin2:Collector
Pin3:Emitter
Pin4:Collector (Case)

 

Ⅳ.Maximum Ratings of 2N6292

 

Ⅴ.2N6292 Precautions when using and installing

1.Polarity: Make sure the individual pins of the transistor are connected correctly. 2N6292 is a PNP transistor, correct connection is necessary.

2.Heat dissipation: For medium power applications, the 2N6292 may generate some heat. Provide effective heat dissipation to ensure that the device operates within a safe temperature range.

3.Maximum ratings: Do not exceed the maximum rated current, power and voltage of 2N6292. These parameters can usually be found in the device data sheet.

4.Electrostatic protection: Take appropriate protective measures to prevent electrostatic damage. Use appropriate electrostatic discharge (ESD) protection equipment and techniques.

5.Power supply voltage: Make sure the power supply voltage meets the specifications of 2N6292. Do not exceed maximum rated voltage.

6.Soldering temperature: During installation, avoid using high-temperature soldering to avoid damaging the transistor.

7.Power supply noise: When used in amplifiers and other sensitive circuits, pay attention to the influence of power supply noise. Use appropriate power supply filtering and decoupling capacitors.

8.Power supply stability: For applications that require stable power supply, ensure the stability of the power supply voltage to prevent unstable operation of the 2N6292.

Ⅵ.OFF Characteristics of 2N6292

Ⅶ.ON Characteristics of 2N6292

 

Ⅷ.2N6292 alternative model

•BDW93C
•2N6291
•BD139
•TIP32C
•MJ2955

 

Frequently Asked Questions

1.What is the primary purpose of 2N6292?
2N6292 is mainly used for medium-power amplification and switching applications.

2.What precautions should be taken when using 2N6292 in amplifier circuits?
Pay attention to power supply stability, minimize power supply noise, and use appropriate filtering and decoupling capacitors.

3.What are the environmental considerations for 2N6292?
Ensure the operating environment stays within specified temperature and ranges for reliable performance.

4.How should 2N6292 be properly installed to ensure optimal performance?
Ensure correct polarity during installation, provide proper heat dissipation, avoid static discharge, and adhere to the recommended operating conditions outlined in the datasheet.