The Trenz Electronic carrier boards provide functionality for testing, evaluation, and development purposes for 4 cm x 5 cm Trenz Electronic SoMs. The carrier boards are equipped with a broad range of various components and connectors for different configuration setups and needs. On-module functional components and multipurpose I/Os of the SoM's PL and PS logic are connected via board-to-board connectors to the carrier board components and connectors for easy user access.
The usable functionality depends on the plugged 4 cm x 5 cm module.
4 x 5 cm Carriers Legend
Features TE0701 / TE0705
- Trenz Electronic 4 cm x 5 cm module connectors (3 x Samtec LSHM series)
- Overvoltage, undervoltage, and reverse supply protection controller
- Barrel jack for 12 V power supply
- On-board system controller CPLD (Lattice MachXO2 1200 HC), programmable via mini-USB JTAG interface
- Program via ARM® JTAG interface connector or through system controller CPLD via mini-USB JTAG interface
- RJ45 Gigabit Ethernet MagJack with 2 integrated LEDs
- 2 x 40-pin headers for access to module's PL I/O bank pins
- USB JTAG and UART interface (FTDI FT2232H) with mini-USB connector
- 8 x user LEDs (red) routed to system controller CPLD
- 2 x user push buttons routed to system controller CPLD. By default (depending on CPLD firmware) configured as system "RESET" and "RESTART" buttons
- 2 x 4-bit DIP-switch for baseboard configuration
- 2 x 12-pin IDC header socket (vertical) for accessing module's PL I/O bank pins, can be used as LVDS pairs
- 2 x 12-pin IDC header socket (right angle) for accessing module's PL I/O bank pins or PS MIO bank pins (if used with Xilinx Zynq-7000 module)
- 2 x 50-pin IDC header for accessing module's PL I/O bank pins
- Micro SD card socket with card detect switch, can be used for system booting
- Micro-USB interface connected to SoM's USB transceiver (device, host, or OTG modes)
Features TE0703
- Trenz 4 cm x 5 cm module socket (3 x Samtec LSHM series connectors)
- 2 x VG96 backplane connectors (mounting holes and solder pads)
- SDIO port expander with voltage-level translation
- Micro SD card socket, can be used to boot system
- 4 x user LEDs, 2 x red and 2 x green
- Mini-USB connector (USB JTAG and UART interface)
- 1 x user-push button routed to CPLD. By default it is configured as system "RESET" button
- RJ45 Gigabit Ethernet socket with 4 integrated LEDs
- USB host connector
- Barrel jack for 5 V power supply input
- 4 A high-efficiency power SoC DC-DC step-down converter (Enpirion EN6347) for 3.3 V power supply
- USB JTAG and UART interface (FTDI FT2232H), compatible with Xilinx and many other tools (also with many other tools)
- 2 x user configurable DIP switches
Features TEBA0841
- Trenz 4 cm x 5 cm module socket (3 x Samtec LSHM series connectors)
- 1 x XMOD (TE0790) pin header
- 1 x pin header 16 pol. (JTAG, MGT-CLK, boot mode, RST, and I/Os)
- 1 x pin header 10 pol. (SD I/Os)
- 2 x pin headers 50 pol. (FPGA bank I/Os and power)
- 1 x SFP connector
- 1 x Micro-USB
- 1 x pin header for FPGA bank power VCCIOA (M1.8 VOUT, 2.5 V, 3.3 VOUT)
- 1 x LDO voltage regulator 3.3 V to 2.5 V
- 2 x user LED (red / green)
Features TE0706
- VG96 backplane connector and 50-pin IDC male connector socket
- SDIO port expander with voltage-level translation
- Micro SD card socket and a USB type A connector
- 1 x user push button, user configurable DIP switch
- 1 x RJ45 Gigabit Ethernet MagJack
- 1 x Ethernet PHY
- Barrel jack for 5 V power supply input
- DC-DC step-down converter for 3.3 V power supply
- JTAG pins on 12-pin header
- 3 x VCCIO selection jumper
