3
LT1001
1001fb
ELECTRICAL CHARACTERISTICS
LT1001AM/883 LT1001M
SYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
V
OS
Input Offset Voltage ● 30 60 45 160 µV
∆V
OS
Average Offset Voltage Drift ● 0.2 0.6 0.3 1.0 µV/°C
∆Temp
I
OS
Input Offset Current ● 0.8 4.0 1.2 7.6 nA
I
B
Input Bias Current ● ±1.0 ±4.0 ±1.5 ±8.0 nA
A
VOL
Large Signal Voltage Gain R
L
≥ 2kΩ, V
O
= ±10V ● 300 700 200 700 V/mV
CMRR Common Mode Rejection Ratio V
CM
= ±13V ● 110 122 106 120 dB
PSRR Power Supply Rejection Ratio V
S
= ±3 to ±18V ● 104 117 100 117 dB
Input Voltage Range ● ±13 ±14 ±13 ±14 V
V
OUT
Output Voltage Swing R
L
≥ 2kΩ ● ±12.5 ±13.5 ±12.0 ±13.5 V
P
d
Power Dissipation No load ● 55 90 60 100 mW
V
S
= ±15V, –55°C ≤ T
A
≤ 125°C, unless otherwise noted
LT1001AC LT1001C
SYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
V
OS
Input Offset Voltage ● 20 60 30 110 µV
∆V
OS
Average Offset Voltage Drift ● 0.2 0.6 0.3 1.0 µV/°C
∆Temp
I
OS
Input Offset Current ● 0.5 3.5 0.6 5.3 nA
I
B
Input Bias Current ● ±0.7 ±3.5 ±1.0 ±5.5 nA
A
VOL
Large Signal Voltage Gain R
L
≥ 2kΩ, V
O
= ±10V ● 350 750 250 750 V/mV
CMRR Common Mode Rejection Ratio V
CM
= ±13V ● 110 124 106 123 dB
PSRR Power Supply Rejection Ratio V
S
= ±3V to ±18V ● 106 120 103 120 dB
Input Voltage Range ● ±13 ±14 ±13 ±14 V
V
OUT
Output Voltage Swing R
L
≥ 2kΩ ● ±12.5 ±13.8 ±12.5 ±13.8 V
P
d
Power Dissipation No load ● 50 85 55 90 mW
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: Offset voltage for the LT1001AM/883 and LT1001AC are measured
after power is applied and the device is fully warmed up. All other grades
are measured with high speed test equipment, approximately 1 second
after power is applied. The LT1001AM/883 receives 168 hr. burn-in at
125°C. or equivalent.
Note 3: This parameter is tested on a sample basis only.
Note 4: Long Term Input Offset Voltage Stability refers to the averaged
trend line of V
OS
versus Time over extended periods after the first 30 days
of operation. Excluding the initial hour of operation, changes in V
OS
during
the first 30 days are typically 2.5µV.
Note 5: Parameter is guaranteed by design.
Note 6: 10Hz noise voltage density is sample tested on every lot. Devices
100% tested at 10Hz are available on request.
V
S
= ±15V, 0°C ≤ T
A
≤ 70°C, unless otherwise noted
LT1001AM/883
LT1001AC LT1001M/LT1001C
SYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
Input Voltage Range ±13 ±14 ±13 ±14 V
V
OUT
Maximum Output Voltage Swing R
L
≥ 2kΩ±13 ±14 ±13 ±14 V
R
L
≥ 1kΩ±12 ±13.5 ±12 ±13.5 V
S
R
Slew Rate R
L
≥ 2kΩ (Note 5) 0.1 0.25 0.1 0.25 V/µs
GBW Gain-Bandwidth Product (Note 5) 0.4 0.8 0.4 0.8 MHz
P
d
Power Dissipation No load 46 75 48 80 mW
No load, V
S
= ±3V 4 6 4 8 mW
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
S
= ±15V, T
A
= 25°C, unless otherwise noted
