LTC1982ES6#TRMPBF

LTC1981/LTC1982
7
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
PACKAGE DESCRIPTIO
U
Dimensions in inches (millimeters) unless otherwise noted.
S5 Package
5-Lead Plastic SOT-23
(LTC DWG # 05-08-1633)
APPLICATIONS INFORMATION
WUU
U
S6 Package
6-Lead Plastic SOT-23
(LTC DWG # 05-08-1634)
0.95
(0.037)
REF
1.50 – 1.75
(0.059 – 0.069)
0.35 – 0.55
(0.014 – 0.022)
0.35 – 0.50
(0.014 – 0.020)
FIVE PLACES (NOTE 2)
S5 SOT-23 0599
2.80 – 3.00
(0.110 – 0.118)
(NOTE 3)
1.90
(0.074)
REF
0.90 – 1.45
(0.035 – 0.057)
0.90 – 1.30
(0.035 – 0.051)
0.00 – 0.15
(0.00 – 0.006)
0.09 – 0.20
(0.004 – 0.008)
(NOTE 2)
2.60 – 3.00
(0.102 – 0.118)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DIMENSIONS ARE INCLUSIVE OF PLATING
3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
4. MOLD FLASH SHALL NOT EXCEED 0.254mm
5. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ)
0.95
(0.037)
REF
1.50 – 1.75
(0.059 – 0.069)
0.35 – 0.55
(0.014 – 0.022)
0.35 – 0.50
(0.014 – 0.020)
SIX PLACES (NOTE 2)
S6 SOT-23 0898
2.80 – 3.00
(0.110 – 0.118)
(NOTE 3)
1.90
(0.074)
REF
0.90 – 1.45
(0.035 – 0.057)
0.90 – 1.30
(0.035 – 0.051)
0.00 – 0.15
(0.00 – 0.006)
0.09 – 0.20
(0.004 – 0.008)
(NOTE 2)
2.6 – 3.0
(0.110 – 0.118)
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DIMENSIONS ARE INCLUSIVE OF PLATING
3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
4. MOLD FLASH SHALL NOT EXCEED 0.254mm
5. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ)
Figure 4. Reverse Battery Protection
V
CC
GATE
SHDN
GND
GDR
LTC1981
LOAD
1981/82 F04
3V
V
BAT
(1.8V TO 5V)
Si3442DV
10k
10k
0.1µF
1
2
3
5
4
150
GATE
DRIVE
READY
Reverse Battery Protection
The LTC1981/LTC1982 can be protected against reverse
battery conditions by connecting a 150 resistor in series
with the supply pin as shown in Figure 4. The resistor
limits the supply current to less than 24mA with –3.6V
applied. Because the LTC1981/LTC1982 draw very little
current while in normal operation, the drop across the
resistor is minimal. Control logic can be protected by
adding 10k resistors in series with the input pins.
LTC1981/LTC1982
8
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
FAX: (408) 434-0507
www.linear-tech.com
LINEAR TECHNOLOGY CORPORATION 2000
sn19812 19812fs LT/LCG 1200 4K • PRINTED IN USA
RELATED PARTS
PART NUMBER DESCRIPTION COMMENTS
LTC1153/LTC1154 Single High Side Micropower MOSFET Drivers Circuit Breaker with Auto Reset
LTC1155/LTC1255 Dual High Side Micropower MOSFET Drivers Latchoff Current Limit
LTC1163/LTC1165 Triple 1.8V to 6V High Side MOSFET Driver Three MOSFET Drivers in 8-Lead SO Package
LTC1623 SMBus Dual High Side Switch Controller Uses External Switches, Two Three-State Address Pins
LTC1710 SMBus Dual Monolithic High Side Switch Uses Internal Switches, One Three-State Address Pin
Driving Both High Side and Low Side Switches
U
TYPICAL APPLICATIO
SHDN 1
GND
SHDN 2
LTC1982
GATE 1
GATE 2
V
CC
SHDN 1
SHDN 2
HIGH SIDE
LOAD
LOW SIDE
LOAD
10µF
0.1µF
0.1µF
1k
1k
Q1
Si6954DQ
Q2
Si6954DQ
V
CC
1.8 to 5.0V
V
EXT
(30V MAX)
1981/82 • TA03
1
2
3
6
5
4

LTC1982ES6#TRMPBF

Mfr. #:
Manufacturer:
Analog Devices / Linear Technology
Description:
Gate Drivers Dual Micropower Hi Side Sw Controller
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union