MC100LVEP16DR2G

MC10LVEP16, MC100LVEP16
www.onsemi.com
4
Table 4. 10EP DC CHARACTERISTICS, PECL (V
CC
= 2.5 V, V
EE
= 0 V (Note 1))
40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 17 22 27 17 22 27 17 22 28 mA
V
OH
Output HIGH Voltage (Note 2) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV
V
OL
Output LOW Voltage (Note 2) 565 740 865 630 805 930 690 865 990 mV
V
IHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Notes 3, 4)
1.2 2.5 1.2 2.5 1.2 2.5 V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current
D
D
0.5
150
0.5
150
0.5
150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary +0.125 V to 1.3 V.
2. All loading with 50ĂW to V
CC
2.0 V.
3. Do not use V
BB
at V
CC
< 3.0 V. Single ended input CLK pin operation is limited to V
CC
3.0 V in PECL mode.
4. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential
input signal.
Table 5. 10EP DC CHARACTERISTICS, PECL (V
CC
= 3.3 V, V
EE
= 0 V (Note 1))
40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 17 22 27 17 22 27 17 22 28 mA
V
OH
Output HIGH Voltage (Note 2) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV
V
OL
Output LOW Voltage (Note 2) 1365 1540 1665 1430 1605 1730 1490 1665 1790 mV
V
IH
Input HIGH Voltage (Single Ended) 2090 2415 2155 2480 2215 2540 mV
V
IL
Input LOW Voltage (Single Ended) 1365 1690 1430 1755 1490 1815 mV
V
BB
Output Voltage Reference (Note 3) 1790 1890 1990 1855 1955 2055 1915 2015 2115 mV
V
IHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 4)
1.2 3.3 1.2 3.3 1.2 3.3 V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current
D
D
0.5
150
0.5
150
0.5
150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary +0.925 V to 0.5 V.
2. All loading with 50 W to V
CC
2.0 V.
3. Single ended input CLK pin operation is limited to V
CC
3.0 V in PECL mode.
4. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential
input signal.
MC10LVEP16, MC100LVEP16
www.onsemi.com
5
Table 6. 10EP DC CHARACTERISTICS, NECL (V
CC
= 0 V, V
EE
= 3.8 V to 2.375 V (Note 1))
40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 17 22 27 17 22 27 17 22 28 mA
VOH Output HIGH Voltage (Note 2) 1135 1010 885 1070 945 820 1010 885 760 mV
V
OL
Output LOW Voltage (Note 2) 1935 1760 1635 1870 1695 1570 1810 1635 1510 mV
V
IH
Input HIGH Voltage (Single Ended) 1210 885 1145 820 1085 760 mV
V
IL
Input LOW Voltage (Single Ended) 1935 1610 1870 1545 1810 1485 mV
V
BB
Output Voltage Reference (Note 3) 1510 1410 1310 1445 1345 1245 1385 1285 1185 mV
V
IHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 4)
V
EE
+1.2 0.0 V
EE
+1.2 0.0 V
EE
+1.2 0.0 V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current
D
D
0.5
150
0.5
150
0.5
150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
.
2. All loading with 50ĂW to V
CC
2.0 V.
3. Single ended input CLK pin operation is limited to V
EE
3.0 V in NECL mode.
4. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential
input signal.
Table 7. 100EP DC CHARACTERISTICS, PECL (V
CC
= 2.5 V, V
EE
= 0 V (Note 1))
40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 19 24 29 22 28 34 24 30 36 mA
V
OH
Output HIGH Voltage (Note 2) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV
V
OL
Output LOW Voltage (Note 2) 555 730 900 555 730 900 555 730 900 mV
V
IHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Notes 3, 4)
1.2 3.3 1.2 3.3 1.2 3.3 V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current
D
D
0.5
150
0.5
150
0.5
150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary +0.125 V to 1.3 V.
2. All loading with 50 W to V
CC
2.0 V.
3. Do not use V
BB
at V
CC
<3.0 V. Single ended input CLK pin operation is limited to V
CC
3.0 V in PECL mode.
4. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential
input signal.
MC10LVEP16, MC100LVEP16
www.onsemi.com
6
Table 8. 100EP DC CHARACTERISTICS, PECL (V
CC
= 3.3 V, V
EE
= 0 V (Note 1))
40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 19 24 29 22 28 34 24 30 36 mA
V
OH
Output HIGH Voltage (Note 2) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV
V
OL
Output LOW Voltage (Note 2) 1355 1530 1700 1355 1530 1700 1355 1530 1700 mV
V
IH
Input HIGH Voltage (Single Ended) 2135 2420 2135 2420 2135 2420 mV
V
IL
Input LOW Voltage (Single Ended) 1355 1700 1355 1700 1355 1700 mV
V
BB
Output Voltage Reference (Note 3) 1775 1875 1975 1775 1875 1975 1775 1875 1975 mV
V
IHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 4)
1.2 3.3 1.2 3.3 1.2 3.3 V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current
D
D
0.5
150
0.5
150
0.5
150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary +0.925 V to 0.5 V.
2. All loading with 50ĂW to V
CC
2.0 V.
3. Single ended input CLK pin operation is limited to V
CC
3.0 V in PECL mode.
4. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential
input signal.
Table 9. 100EP DC CHARACTERISTICS, NECL (V
CC
= 0 V, V
EE
= 3.8 V to 2.375 V (Note 1))
40°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 19 24 29 22 28 34 24 30 36 mA
V
OH
Output HIGH Voltage (Note 2) 1145 1020 895 1145 1020 895 1145 1020 895 mV
V
OL
Output LOW Voltage (Note 2) 1945 1770 1600 1945 1770 1600 1945 1770 1600 mV
V
IH
Input HIGH Voltage (Single Ended) 1165 880 1165 880 1165 880 mV
V
IL
Input LOW Voltage (Single Ended) 1945 1600 1945 1600 1945 1600 mV
V
BB
Output Voltage Reference (Note 3) 1525 1425 1325 1525 1425 1325 1525 1425 1325 mV
V
IHCMR
Input HIGH Voltage Common Mode
Range (Differential Configuration)
(Note 4)
V
EE
+1.2 0.0 V
EE
+1.2 0.0 V
EE
+1.2 0.0 V
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current
D
D
0.5
150
0.5
150
0.5
150
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
.
2. All loading with 50 W to V
CC
2.0 V.
3. Single ended input CLK pin operation is limited to V
EE
3.0 V in NECL mode.
4. V
IHCMR
min varies 1:1 with V
EE
, V
IHCMR
max varies 1:1 with V
CC
. The V
IHCMR
range is referenced to the most positive side of the differential
input signal.

MC100LVEP16DR2G

Mfr. #:
Manufacturer:
ON Semiconductor
Description:
Bus Transceivers 2.5V/3.3V ECL Diff
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union