OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

DLW5BTH251TQ2L

P1-P3P4-P6P7-P9P10-P10
Spec. No. JEFL243C-9120-01 P 1/10
MURATA MFG CO., LTD.
Reference Only
Wire Wound Chip Common Mode Choke Coil
DLW5BTH□□□TQ2□
Reference Specification [AEC-Q200]
1. Scope
This reference specification applies to Wire Wound Chip Common Mode Choke Coil DLW5BTH_TQ Series for
Automotive Electronics based on AEC-Q200.
2. Part Numbering
(ex.) DL W 5B T H 102 T Q 2 L
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)
(1) Chip Common Mode Choke Coil
(2) Structure (W : Winding Type)
(3) Dimension (L×W)
(4) Type
(5) Category
3.Rating
Customer
Part Number
MURATA
Part Number
Impedance
at 10MHz,
Under Standard
Tesiting Conditions
(Ω min.)
Impedance
at 100MHz,
Under Standard
Tesiting Conditions
(Ω Typ.)
Rated
Voltage
V(DC)
Withstanding
Voltage
V(DC)
Rated
Current(*)
(A)
DC
Resistance
(Rdc)
(Ωmax.)
Insulation
Resistance
(MΩ min.)
ESD
Rank
2.2kV
at
105℃
at
125℃
DLW5BTH101TQ2L
10 100
50 125
4.0 2.5 0.013
10 2
DLW5BTH101TQ2K
DLW5BTH101TQ2B
DLW5BTH251TQ2L
20 250 3.0 2.0 0.020
DLW5BTH251TQ2K
DLW5BTH251TQ2B
DLW5BTH501TQ2L
30 500 2.5 1.5 0.027
DLW5BTH501TQ2K
DLW5BTH501TQ2B
DLW5BTH102TQ2L
60 1000 2.0 1.2 0.034
DLW5BTH102TQ2K
DLW5BTH102TQ2B
DLW5BTH142TQ2L
100 1400 1.5 1.0 0.056
DLW5BTH142TQ2K
DLW5BTH142TQ2B
(*)As for DLW5BTH_TQ type Rated Current is derated as following figure depending on the operating temperature.
· Operating Temperature : - 40 °C to + 125 °C · Storage Temperature : - 40 °C to + 125 °C
(6) Impedance (Typ. at 100MHz)
(7) Circuit
(8) Features
(9) Number of Line
(10) Packaging Code L : Taping (φ180mm/reel)
K : Taping (φ330mm/reel)
B : Bulk
Rated Current
at 105℃
Rated Current
at 125℃
105
125
Operating Temperature
(
Ambient temperature
)[℃]
Rated Current [A]
Spec. No. JEFL243C-9120-01 P 2/10
MURATA MFG CO., LTD.
Reference Only
4. Standard Testing Conditions
< Unless otherwise specified > < In case of doubt >
Temperature : Ordinary Temp. 15 ºC to 35 °C Temperature : 20 °C ± 2 °C
Humidity : Ordinary Humidity 25 %(RH) to 85 %(RH) Humidity : 60 %(RH) to 70 %(RH)
Atmospheric pressure : 86 kPa to 106 kPa
5. Style and Dimensions
■ Unit Mass (Typical value)
0.21g
（in: mm）
No polarity
6. Marking
7. Electrical Performance
No. Item Specifications Test Method
7.1 Impedance
(|Z|) (at 10MHz)
Meet item 3. Measuring Equipment : KEYSIGHT 4191A or the
equivalents.
Measuring Frequency : 10MHz (ref. Item 9.)
7.2 Insulation
Resistance
(I.R.)
Measuring Equipment : R8340A or the equivalents.
Measuring voltage : Rated Voltage
Time : within 60 s (ref. Item 9.)
7.3 DC Resistance
(Rdc)
Measuring Current : 100 mA max. (ref. Item 9.)
(In case of doubt in the above mentioned standard
condition,measure by 4 terminal method.)
・
Top of the tape
Tape
DLW5BT
Sprocket Hole
marking
(L)5.0±0.3
(W)5.0±0.3
3.6±0.3
±0.3
1.3
±0.3
0.9
±0.3
1.3
①
②
1.7
±0.3
1.7
±0.3
1.3
±0.3
:
Electrode
④③
0.5
min.
0.45min
.
2.35±0.15
3.0±0.5
0.5±0.3
:
M
arking
(TOP)
①
④
②
③
■
Equivalent Circuites
Spec. No. JEFL243C-9120-01 P 3/10
MURATA MFG CO., LTD.
Reference Only
No. Item Specifications Test Method
7.4 Withstanding
Voltage
Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage
Time : 1 to 5 seconds
Charge Current : 1 mA max. (ref. Item 9.)
8. Q200 Requirement
7-1. Performance (based on Table 13 for Ferrite EMI SUPPRESSORS/FILTERS)
AEC-Q200 Rev.D issued June 1. 2010
AEC-Q200
Murata Specification / Deviation
No. Stress Test Method
3 High
Temperature
Exposure
1000hours at 125 deg C
Set for 24hours at room temperature,
then measured.
Meet Table A after testing.
Table A
4 Temperature Cycling 1000cycles
-40 deg C to +125 deg C
Set for 24hours at room temperature,
then measured.
Meet Table A after testing.
5 Destructive
Physical Analysis
Per EIA469
No electrical tests
Not Applicable
7 Biased Humidity 1000hours at 85 deg C, 85%RH
Apply max rated voltage and current.
Meet Table A after testing.
Apply rated voltage.
(ref.item 9)
8 Operational Life Apply 125 deg C
1000hours
Set for 24hours at room temperature,
then measured
Meet Table A after testing.
Apply derating of rated current.
(ref.item 9)
9 External Visual Visual inspection No abnormalities
10 Physical Dimension Meet ITEM 5
（Style and Dimensions）
No defects
12 Resistance to
Solvents
Per MIL-STD-202 Method 215 Not Applicable
13 Mechanical Shock
Per MIL-STD-202 Method 213
Conditon F:
1500g’s(14.7N)/0.5ms/
Half sine
Meet Table A after testing.
14 Vibration 5g's(0.049N) for 20 minutes, 12cycles
each of 3 oritentations
Test from 10-2000Hz.
12cycles each of 3 orientations
Meet Table A after testing.
15 Resistance
to Soldering Heat
No-heating
Solder temperature
260C+/-5 deg C
Immersion time 10s
Pre-heating：150 to 180C / 90±30s
Meet Table A after testing.
17 ESD
Per AEC-Q200-002 Meet Table A after testing.
ESD Rank: Refer to Item 3. Rating.
Appearance No damaged.
Impedance
change
(at 10MHz)
within ± 20%
I.R. 10MΩ min.
Withstanding
Voltage
No damaged.
P1-P3P4-P6P7-P9P10-P10

DLW5BTH251TQ2L

Mfr. #:
Buy DLW5BTH251TQ2L
Manufacturer:
Murata Electronics
Description:
Common Mode Chokes / Filters 250ohms 3A 50VDC AECQ200 Pwrtrain/Saf
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet