SPECIFICATION
MODEL
LCM-40U
DC VOLTAGE RANGE
RATED POWER
OUTPUT
SETUP TIME
Note.3
VOLTAGE RANGE Note.2
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
Note.4
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
DALI STANDARDS
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSION
OTHERS
NOTE
PACKING
2 ~ 100V 2 ~ 59V2 ~ 70V 2 ~ 50V 2 ~ 39V 2 ~ V34
35W
110
76V
1000ms / 115VAC
90 ~ 132VAC 127 ~ 186VDC
47 ~ 63Hz
87.5%
Compliance to FCC part 15 Subpart B
20 ~ 90% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
193.6K hrs min. MIL-HDBK-217F (25 )℃
123.5*81.5*23mm (L*W*H)
1. All parameters NOT specially mentioned are measured at 115VAC input, rated current and 25 of ambient temperature.℃
2. De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details
3. Length of set up time is measured at first cold start. Turning ON/OFF the driver may lead to increase of the set up time.
4. Efficiency is measured at 700mA/72V output set by DIP switch.
5. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. It is measured 60%~100% of maximum voltage under rated power delivery.
0.28Kg ; 54pcs/16Kg/1.12CUFT
OPEN CIRCUIT VOLTAGE (max.)
ENVIRONMENT
SAFETY &
FUNCTION
EMC
PROTECTION
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3.75KVAC
UL8750 approved
Comply with IEC62386-101, 102, 207
I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH℃
CURRENT LEVEL
350mA 600mA500mA 700mA(default) 900mA 1050mA
CURRENT TOLERANCE
EMC EMISSION
SHORT CIRCUIT
OVER VOLTAGE
OVER TEMPERATURE
TEMP. COMPENSATION
SYNCHRONIZATION
Constant current limiting, recovers automatically after fault condition is removed
Shutdown o/p voltage,re-power on to recover
Please refer to "SYNCHRONIZATION OPERATION” section
DIMMING
WIRELESS PROTOCOL(Optional)
Please refer to "DIMMING OPERATION" section
EnOcean standard 902 MHz or USA/Canada; Max. device(switch) saved into the memory : 33
Shutdown o/p voltage, re-power on to recover
110 ~ 130V
By external NTC, please refer to “TEMPERATURE COMPENSATION OPERATION”section
TOTAL HARMONIC DISTORTION
<0.5mA / 120VAC
0.43A/115VAC
PF VAC @full load≧0.98/115
(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
COLD START 15A(t =270 s measured at 50% I ) at 115VAC
width peakμ ; Per NEMA 410
±5%
±0.03%/ (0 ~ 40 )℃℃
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
22 units (circuit breaker of type B) / 38 units (circuit breaker of type C) at 115VAC
File Name:LCM-40U-SPEC 2016-11-23
35W Multiple-Stage Constant Current Mode LED Driver
LCM-40U series
(Please refer to "STATIC CHARACTERISTIC" section)
WORKING TEMP.
MAX. CASE TEMP.
Tcase=+90℃
Tcase=-30 ~ +90 (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)℃
AUXILIARY DC OUTPUT
Nominal 12V(deviation 11.4~12.6V)@50mA
CURRENT RIPPLE
Note.6
5.0% max. @rated current
Current level selectable via DIP switch, please refer to”DIP SWITCH TABLE” section
THD< 20%(@load 60%)≧
(Please refer to “TOTAL HARMONIC DISTORTION(THD)” section)
