1
MAX DRAFT (TYP)
DO NOT
SCALE FROM
THIS PRINT
IPBD-XX-D-X
No OF POSITIONS
-02 THRU -15
(PER ROW)
[SEE FIG. 2 FOR -02 POSITION]
ROW SPECIFICATION
-D: DOUBLE
OPTION
-R: RETENTION LATCH
(SEE SHEET 3, FIG 3)
(SEE NOTE 16)
-K: KEYED POLARIZATION
(SEE FIG. 5 & 6,
SHEET 4)
.378
.478
-
.0000
+
.0075
.1650
-
.0050
+
.0015
((No OF POSITIONS -1) x .1650)
.1025
±.0020
"A"
"A"
'B'
'A'
'G'
IPBD-08-D SHOWN
FIG 1
01
09
02
.0050
.0050
S/S BOW
SEE TABLE 1
.280
.480
-
.002
+
.005
"B"
"B"
'C'
'D'
SECTION "A"-"A"
SEE NOTE 2
SEE NOTE 8
SEE NOTE 3
T/B BOW
SEE TABLE 1
'F'
01
09
02
03
06
07
10
16
15
14
05
04
11
08
SEE NOTE 12
((No OF POSITIONS x .1650) + .0400)
.075
±.010
.15
.773
±.006
.485
.060
.100
(NO DRAFT)
.095
±.010
SEE NOTE 11
.012
.002
.070
.045
.100
1
MAX DRAFT (TYP)
'E
'H'
SECTION "B"-"B"
PARTING LINE
SEE NOTE 13
30°
(TYP)
DETAIL 'H'
SCALE 15 : 1
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 5
.XXX:
.003 [.08]
.XXXX:
.0015 [.038]
MATERIAL:
.165 SHROUDED CONTACT BODY
BY:
IPBD-XX-D-X
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
DEAN P
10-24-2001
4
1
SHEET SCALE: 1.5:1
VALOX 457, COLOR NATURAL
F:\DWG\MISC\MKTG\IPBD-XX-D-X-MKT.SLDDRW
MAX REGRIND: 0%
MAX FLASH ALLOWED: .003
MAX GATE VESTIGE: .004
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC LOGO SHALL APPEAR AT ONE LOCATION ON SURFACE SHOWN,
APPROXIMATELY .15 x .09 (BOTH SIDES).
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH
TOOL DEPENDANT CAVITY ID AT THE DISCRETION OF SAMTEC ENGINEERING.
4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 OFF THE
SURFACE OF THE PART.
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. MAX ALLOWABLE BOW: SEE TABLE 1.
7. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.001, UNLESS
OTHERWISE STATED.
8. NUMBER OF POSITIONS (PER ROW) TO BE SHOWN ON THIS SURFACE, SIZE
AND DEPTH SIMILAR TO POSITION 1INDICATOR.
9. GATE PAD MUST BE RECESSED .005. GATE LOCATION IS AT THE MOLDERS DISCRETION.
10. END CORES ARE POLARIZED. CONFIRM GEOMETRY RELATIVE TO POSITION 1
INDICATOR & GATE PAD.
11. POSITION 1 INDICATOR TO BE .0005 MAX DEPTH.
12. EACH POSITION TO BE IDENTIFIED WHERE SHOWN.
13. .0005 MAX MISMATCH PERMISSIBLE (ALL FOUR SIDES).
14. LATCH MUST CYCLE 10 TIMES WITHOUT EVIDENCE OF CRACKING
OR COMPROMISE OF FUNCTION.
15. CHECK THIS FEATURE WITH GO/NOGO GAUGE.
16. OPTION NOT FOR SALE. FOR RETENTION LATCH FEATURE, SEE IPBD-XX-D-ML PRINT.
17. POSITION INDICATOR NOT PRESENT ON 2 & 3 POSITION -R OPTION BODIES.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
REVISION X
