LT3011
4
3011f
PARAMETER CONDITIONS MIN TYP MAX UNITS
Dropout Voltage
V
IN
= V
OUT(NOMINAL)
(Notes 4, 5)
I
LOAD
= 1mA
I
LOAD
= 1mA
l
100 150
220
mV
mV
I
LOAD
= 10mA
I
LOAD
= 10mA
l
200 260
380
mV
mV
I
LOAD
= 50mA
I
LOAD
= 50mA
l
300 370
575
mV
mV
GND Pin Current
V
IN
= V
OUT(NOMINAL)
(Notes 4, 6)
I
LOAD
= 0mA
I
LOAD
= 1mA
I
LOAD
= 10mA
I
LOAD
= 50mA
l
l
l
l
46
105
410
1.9
125
225
750
3.5
μA
μA
μA
mA
Output Voltage Noise C
OUT
= 10μF, I
LOAD
= 50mA, BW = 10Hz to 100kHz, V
OUT
= 1.24V 100 μV
RMS
ADJ Pin Bias Current (Note 7) 30 100 nA
Shutdown Threshold V
OUT
= Off to On
V
OUT
= On to Off
l
l
0.3
1.3
1.1
2V
V
SHDN Pin Current (Note 8) V
SHDN
= 0V
V
SHDN
= 6V
0.5
0.1
2
0.5
μA
μA
Quiescent Current in Shutdown V
IN
= 6V, V
SHDN
= 0V 1 5 μA
PWRGD Trip Point % of Nominal Output Voltage, Output Rising
l
85 90 95 %
PWRGD Trip Point Hysteresis % of Nominal Output Voltage 1.1 %
PWRGD Output Low Voltage I
PWRGD
= 50μA
l
140 250 mV
C
T
Pin Charging Current
l
36 μA
C
T
Pin Voltage Differential V
CT(PWRGD High)
– V
CT(PWRGD Low)
1.67 V
Ripple Rejection V
IN
= 7V (Avg), V
RIPPLE
= 0.5V
P-P
, f
RIPPLE
= 120Hz, I
LOAD
= 50mA 65 85 dB
Current Limit V
IN
= 7V, V
OUT
= 0V
V
IN
= 4V, ΔV
OUT
= –0.1V (Note 2)
l
60
140 mA
mA
Input Reverse Leakage Current V
IN
= –80V, V
OUT
= 0V
l
6mA
Reverse Output Current (Note 9) V
OUT
= 1.24V, V
IN
< 1.24V (Note 2) 8 15 μA
ELECTRICAL CHARACTERISTICS
(LT3011H)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3011 is tested and specifi ed for these conditions with the
ADJ pin connected to the OUT pin.
Note 3: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specifi cation will not apply
for all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 4: To satisfy requirements for minimum input voltage, the LT3011
is tested and specifi ed for these conditions with an external resistor
divider (249k bottom, 409k top) for an output voltage of 3.3V. The external
resistor divider will add a 5μA DC load on the output.
Note 5: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specifi ed output current. In dropout, the
output voltage will be equal to (V
IN
– V
DROPOUT
).
Note 6: GND pin current is tested with V
IN
= V
OUT(NOMINAL)
and a current
source load. This means the device is tested while operating close to its
dropout region. This is the worst-case GND pin current. The GND pin
current will decrease slightly at higher input voltages.
Note 7: ADJ pin bias current fl ows into the ADJ pin.
Note 8: SHDN pin current fl ows out of the SHDN pin.
Note 9: Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current fl ows into the OUT
pin and out the GND pin.
Note 10: The LT3011 regulators are tested and specifi ed under pulse
load conditions such that T
J
≅ T
A
. The LT3011E regulators are 100%
tested at T
A
= 25°C. Performance of the LT3011E over the full –40°C
to 125°C operating junction temperature range is assured by design,
characterization and correlation with statistical process controls. The
LT3011I regulators are guaranteed over the full –40°C to 125°C operating
junction temperature range. The LT3011H is tested to the LT3011H
Electrical Characteristics table at 150°C operating junction temperature.
High junction temperatures degrade operating lifetimes. Operating lifetime
is derated at junction temperatures greater than 125°C.
Note 11: This IC includes overtemperature protection that is intended to protect
the device during momentary overload conditions. Junction temperature will
exceed 125°C (LT3011E/LT3011I) or 150°C (LT3011H) when overtemperature
protection is active. Continuous operation above the specifi ed maximum
operating junction temperature may impair device reliability.
The l
denotes the specifi cations which apply over the –40°C to 150°C operating temperature range, otherwise specifi cations are at T
J
= 25°C.