Narrow pitch connectors P35S (0.35mm pitch)
–2–
ACCTB87E 201602-T
PRODUCT TYPES
Notes: 1. Regarding ordering units; During production: Please make orders in 1-reel units.
For samples, please contact our sales office.
SPECIFICATIONS
1. Characteristics
2. Material and surface treatment
Mated height Number of pins
Part number Packing
Socket Header Inner carton (1-reel) Outer carton
1.5mm
40 AXT140124 AXT240124
3,000 pieces 6,000 pieces
50 AXT150124 AXT250124
60 AXT160124 AXT260124
70 AXT170124 AXT270124
80 AXT180124 AXT280124
100 AXT100124 AXT200124
Item Specifications Conditions
Electrical
characteristics
Rated current 0.25A/pin contact (Max. 4 A at total pin contacts) —
Rated voltage 60V AC/DC —
Dielectric strength 150V AC for 1 min.
Rated voltage is applied for one minute and check for
short circuit or damage with a detection current of 1mA.
Insulation resistance Min. 1,000MΩ (initial) Using 250V DC megger (applied for 1 min.)
Contact resistance Max. 100mΩ
Based on the contact resistance measurement method
specified by JIS C 5402.
Mechanical
characteristics
Composite insertion force Max. 0.981N/pin contact × pin contacts (initial)
Composite removal force Min. 0.0588N/pin contact × pin contacts
Contact holding force
(Socket contact)
Min. 0.981N/pin contact
Measuring the maximum force.
As the contact is axially pull out.
Environmental
characteristics
Ambient temperature –55°C to +85°C No icing or condensation.
Soldering heat resistance
Max. peak temperature of 260°C (on the surface of the
PC board around the connector terminals)
Infrared reflow soldering
300°C within 5 sec. or 350°C within 3 sec. Soldering iron
Storage temperature
–55°C to +85°C (product only)
–40°C to +50°C (emboss packing)
No icing or condensation.
Thermal shock resistance
(header and socket mated)
5 cycles, insulation resistance min. 100MΩ,
contact resistance max. 100mΩ
Conformed to MIL-STD-202F, method 107G
Humidity resistance
(header and socket mated)
120 hours, insulation resistance min. 100MΩ,
contact resistance max. 100mΩ
Conformed to IEC60068-2-78
Temperature 40°C±2°C, humidity 90% to 95% R.H.
Saltwater spray resistance
(header and socket mated)
24 hours, insulation resistance min. 100MΩ,
contact resistance max. 100mΩ
Conformed to IEC60068-2-11
Temperature 35°C±2°C, saltwater concentration 5%±1%
H2S resistance
(header and socket mated)
48 hours,
contact resistance max. 100mΩ
Temperature 40°C±2°C,
gas concentration 3 ppm ±1 ppm,
humidity 75% to 80% R.H.
Lifetime
characteristics
Insertion and removal life 50 times
Repeated insertion and removal speed of
max. 200 times/hours
Unit weight 50 pin contacts Socket: 0.06 g Header: 0.03 g
Part name Material Surface treatment
Molded portion LCP resin (UL94V-0) —
Contact and Post Copper alloy
Contact portion: Ni plating on base, Au plating on surface
Terminal portion: Ni plating on base, Au plating on surface (Except for front edge of terminal)
However, the area adjacent to the socket terminal is exposed to Ni on base.
Soldering terminals portion;
Socket: Ni plating on base, Pd + Au flash plating on surface (Expect for front edge of terminal)
Header: Ni plating on base, Au plating on surface (Expect for front edge of terminal)
Order Temperature (°C) Time (minutes)
1
2
3
4
–55
85
–55
0
−3
30
Max. 5
30
Max. 5
+3
0
0
−3
