L±0.3
φD±0.5
B±0.2
(P)
(C)(C)
0.4±0.2
A±0.2
0.3MAX
W
&KLS7\SH
Specifications
Outline Drawing
Item Performance
Category temperature range (℃)
Tolerance at rated capacitance (%)
Leakage current (µA)
*Note
Tangent of loss angle (tanδ)
Characteristics at high
and low temperature
Endurance (105℃)
(Applied ripple current)
Damp heat, steady state
(humidity)
60℃, 90 to 95%RH
Characteristics of applied
surge voltage
Failure tare
*
Note : If any doubt arises, measure the leakage current after following voltage application treatment.
Voltage application treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105℃.
0.5% per 1000 hours max
i
mum (Confidence level 60% at 105℃)
C : Rated capacitance (µF) ; V : Rated voltage (V)
25,352.5 to 20Rated voltage (V)
Less than 0.5 CVLess than 0.2 CVLeakage current (µA)
Test time
Leakage current
Percentage of capacitance change
Tangent of the loss angle
E.S.R. change
2000 hours
The initial specified value or less
Within
±
20% of initial value
150% or less of the initial specified value
200% or less of the initial specified value
Test time
Leakage current
Percentage of capacitance change
Tangent of the loss angle
E.S.R. change
500 hours
The initial specified value or less
Within
±
20% of initial value
150% or less of the initial specified value
200% or less of the initial specified value
Leakage current
Percentage of capacitance change
Tangent of the loss angle
E.S.R. change
The initial specified value or less
Within
±
20% of initial value
150% or less of the initial specified value
200% or less of the initial specified value
Impedance ratio (max.)
Unit : mm
Part numbering system (example : 4V150µF)
PVH ̶ V
Series code
4 151 M
Rated voltage
symbol
Rated capacitance
symbol
Capacitance
tolerance symbol
F60
Casing
symbol
̶
Taping
symbol
Less than 0.12
The capacitors shall be subject to 1000 cycles each consisting of charge with the surge voltage specified at 15 to 35℃ for 30 seconds
through a protective resister (Rc＝1kΩ) in 6 minutes per cycle. Surge voltage : 1.15 times of rated voltage
( ) : Reference size
6.3
8
10
φD
5.7
6.7
7.7
L
6.6
8.4
10.4
A
6.6
8.4
10.4
B
2.7
3.0
3.2
C
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
W
F60
G70
H80
Casing symbol
2.0
3.1
4.7
P
PVH
E
●
Super low E.S.R. and high ripple current are realized.
●
Guaranteed 105℃, 2000 hours.
−55 to ＋105
±20 (20℃,120Hz)
(20℃,120Hz)
(100kHz)Ｚ−５5 ℃ /Ｚ＋2 0 ℃ : 1.50
(20℃)
●
Soldering conditions are described on page 13.
●
Land pattern size are described on page 11.
●
The taping specifications are described on page 14.
*5((1
&$3
$QWL
FOHDQLQJ
VROYHQW
60'
Ý&
KRXUV
/RZ
(65
Aluminum Electrolytic Capacitors
With Conductive Polymer Solid
Electrolyte
34
CAT.No.2013/2014E
NOTE
Design, Specifications are subject to change without notice.
Ask factory for technical specifications before purchase and/or use.
®
PVH
ALUMINUM ELECTROLYTIC CAPACITORS
WITH CONDUCTIVE POLYMER SOLID ELECTROLYTE
