852-10155

iv
NOTES:
5
SPECIFICATIONS
DC Input Voltage:
AC Adapter Input Load: 100/240 ±10% VAC, 0.25A, 50/60 Hz, 5 VDC output with
maximum output current of 1A Unit Power Consumption (Typical): 600 mA @ 5
VDC
Operating Temperature:
32° to 122° F (0° to 50° C)
Storage Temperature:
-4° to 158° F (-20° to 70° C)
Humidity:
5 to 90% (non-condensing); 0 to 10,000 ft. altitude
Dimensions:
H=0.92” W=3.50” D=4.00” (2.3 x 8.9 x 10.2 cm)
4
Fiber Uplink Port
The LED indicator for the fiber uplink port is located on the RJ-45 connector of the
downlink port next to the power connector. There are four LED functions for the
fiber uplink port.
The fiber uplink port LED functions are as follows:
Glows green when a link is established on the fiber port.
Glows green indicating a valid link, then blinks green when activity is detected
on the fiber port.
When the LED is OFF, there is no link (check cabling, check remote device).
Blinking LED - indicates the device attached to the other end of the fiber
maybe passing Link Fault Propagation, or generating noise onto the fiber. This
normally happens when there is a media converter at the fiber end of the link.
Connect the second port of the converter onto a valid device to generate link.
Twisted Pair Uplink Port
When the Access Converter/3 is configured with a twisted pair uplink port, the LED
location and functionality is the same as that for the downlink ports.
1
ABOUT THE ACCESS CONVERTER/3
The Access Converter/3 is a 10/100 auto-negotiating, switching, optical access
product. There is one uplink port and three 10/100 twisted pair downlink ports.
The uplink port can be either fiber or 10/100 twisted pair. The uplink port is
located on the back of the media converter. Each of the twisted pair ports can
auto-sense the speed and duplex mode of a connected device. These speeds
include the following:
10 Mbps
100 Mbps
Half Duplex
Full Duplex
All of these speeds include Flow Control. The fiber port always operates at 100
Mbps Full Duplex.
The Access Converter/3 offers plug-and-play operation, including the AutoCross
feature which automatically selects between a crossover work-station or straight-
through repeater hub connection depending on the connected device.
The Access Converter/3 also protects against Broadcast storms, and allows packets
of up to 1916 bytes to pass. The Access Converter/3 uses a universal external
switching power adapter for 100 to 240 ±10% VAC input and 5 VDC output
(included).
2
INSTALLING THE ACCESS CONVERTER/3
Install the Access Converter/3 as a table-top device, or mount to a wall surface with
the appropriate bracket (included). To wall mount, use the supplied screws to
attach the wall-mount bracket to the Access Converter/3, then simply mount the
unit to the wall by tightening the screws (not supplied).
Note
The Access Converter/3 packaging also includes four small rubber “feet” for use in
table-top or wall-mount installations.
Plug the Access Converter/3 into a power source and attach the connected devices.
Verify installation by observing the LEDs on the unit (refer to the LED Operation
section for more information).
Wall Mount Bracket
Screw holes for mounting unit to the wall.
Wall-mount bracket must be attached
to the bottom of the unit.
Screw holes for mounting
wall-mount bracket with
supplied screws
3
LED OPERATION
Each Access Converter/3 includes diagnostic LEDs for troubleshooting.
Front
Back
Twisted Pair Downlink Ports
The LED indicator for the twisted pair downlink port is located on the RJ-45
connector of the downlink port next to the power connector. There are two LED
functions for the twisted pair downlink ports. LED functions are as follows:
Glows amber when a link is established on the copper port
Glows amber indicating a valid link, then blinks amber when activity is
detected on the copper port.
Note
The
g
reen LED on RJ-45 connectors
are
reserved for future use, with one
exception— refer to the following Uplink Port sections for more information.
Uplink LED
Fiber Uplink
LED
TX Downlink LED

852-10155

Mfr. #:
Manufacturer:
B+B SmartWorx
Description:
Ethernet Modules AccessConverter TX/3 SSFX-SM1310/PLUS-SC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet