1/9
www.rohm.com
2010.06 - Rev.A
© 2010 ROHM Co., Ltd. All rights reserved.
Sound Processors for Home Theater Systems
2ch
Electronic Volume
BD3812F
Description
BD3812F is an electronic volume having volume, gain amplifier functions necessary for applications in AV receivers, home
theatre systems, min-component systems and so forth. Having a chip select terminal, it can be controlled until 4 chips with
common bus line.
Features
1) Residual noise : 1.2µVrms {dynamic range : 131dB (IHF-A)}
2) 2ch independent volume (0 to -103dB, MUTE 1dB/step)
3) 8ch at maximum available in combination of any of BD3811K1, BD3813KS, BD3814FV, BD3815KS (6ch volume)
in common bus line
4) It can be controlled until 4 chips with common bus line at the same time
5) Maximum output voltage : 4.2Vrms (Vcc=7, VEE=-7V, RL=10k)
6) 2-line serial control (for both 3.3V and 5V)
7) Built-in Output gain amplifier for adjustment of output signal voltage (0, 6 to 18dB, 2dB/step)
8) Output mute controllable by serial data and external control terminal
Applications
AV receivers, home theater systems, mini-component systems, etc.
Absolute maximum ratings (Ta=25)
Parameter Symbol Ratings Unit
Powewr supply voltage
VCC 7.5
*
1
V
VEE -7.5
Input signal voltage VIN VCC+0.3 to VEE-0.3 V
Power dissipation Pd 450
*2
mW
Operating temperature range Topr 20 to +75
Storage temperature range Tastg 55 to +125
*1 Even in the specified range of Power Supply Voltage, applying voltage only to the VCC side may
cause an excessive current to give a permanent damage to the IC.
When starting up power supplies, VEE and VCC should be powered on simultaneously or VEE first; then followed by VCC.
*2 Over Ta25°C, reduce at the rate of 4.5mW/°C. When installed on the standard board (size: 70x70x1.6mm).
Operating conditions
It must function normally at Ta25°C.
Parameter Symbol
Ratings
Unit
Min. Typ. Max.
Operating source voltage
VCC 5 7 7.3
V
VEE -7.3 -7 -5
No.10081EAT03
Technical Note
2/9
www.rohm.com
2010.06 - Rev.A
© 2010 ROHM Co., Ltd. All rights reserved.
BD3812F
Electrical characteristics
Ta=25, VCC=7V, VEE-7V, f=1kHz, Vin=1Vrms, RL=10kΩ, Rg=600Ω, Master volume=0dB, Output gain=0dB , unless
otherwise specified.
Parameter
Symbol
Limits
Unit Conditions
Min. Typ. Max.
Circuit current
VCC
IQ
2 6
mA No signal
VEE -6 -2
Output voltage gain Gv -2 0 2 dB Measure : Pin14, 13
Total harmonic distortion ratio THD 0.005 0.09 %
Measure : Pin14, 13
BW=40030kHz
Maximum output voltage Vomax 3.4 4.2 Vrms
Measure : Pin14, 13
THD=1%
Output noise voltage Vno 1.2 5 µVrms
Measure : Pin 14, 13
Rg=0Ω, BW=IHF-A
Input impedance Rin 20 30 40 kΩ Measure : Pin1, 3
Cross talk between channels
1ch2ch
CTC12 -100 -70 dB
Measure : Pin13(OUT2)
Rg=0Ω, BW=IHF-A
Reference : Pin14(OUT1)=1Vrms
Cross talk between channels
2ch1ch
CTC21 -100 -70 dB
Measure : Pin14(OUT1)
Rg=0Ω, BW=IHF-A
Reference : Pin13(OUT2)=1Vrms
Volume control range GVR -106 -103 -100 dB
Measure : Pin 14, 13
Vin=3Vrms
Volume set error 1 VE1 -2 0 2 dB
Measure : Pin 14, 13
0 to –53dB, Vin=3Vrms
Volume set error 2 VE2 -3 0 3 dB
Measure : Pin 14, 13
-54 to –103dB, Vin=3Vrms
Maximum attenuation Vmin -118 -105 dB
Measure : Pin 14, 13
BW=IHF-A, Vin=3Vrms
Output gain control range GOG 16 18 20 dB
Measure : Pin 14, 13
Vin=0.4Vrms
Output gain set error GOE -2 0 -2 dB
Measure : Pin 14, 13
Vin=0.4Vrms
* This product is not of “anti radiation design”.
Technical Note
3/9
www.rohm.com
2010.06 - Rev.A
© 2010 ROHM Co., Ltd. All rights reserved.
BD3812F
Timing chart
1) Signal timing conditions
Data is read on the rising edge of the clock.
Latch is read on the falling edge of the clock.
Latch signal must terminate with the LOW state.
* To avoid malfunctions, clock and data signals must terminate with the LOW state.
Fig.1
Parameter Symbol
Limits
Unit
Min. Typ. Max.
Minimum clock width twc 2.0 µs
Minimum data width twd 2.0 µs
Minimum latch width twl 2.0 µs
LOW hold width twh 2.0 µs
Data setup time
(DATACLK)
tsd 1.0 µs
Data hold time(CLKDATA) thd 1.0 µs
Latch setup time(CLKLATCH) tsl 1.0 µs
Latch hold time(DATALATCH) thl 1.0 µs
Latch low setup time ts 1.0 µs
Latch low hold time th 1.0 µs
2) Voltage conditions for control signal
Parameter Condition
Limits
Unit
Min. Typ. Max.(Vcc)
“H”input voltage
Vcc=57.3V
VEE=-5-7.3V
2.2 5.5 V
“L” input voltage 0 1.0 V
CL
(CLOCK)
DA
DATA
LATCH
thd thdth ts tsl thl tsd
twc
twh
twd
twl
DATA DATA
LATCH
90% 90% 90% 90%
10% 10% 10%
90% 90% 90%
90% 90%
10%
10% 10%
twc
Terminate
with Low.

BD3812F-E2

Mfr. #:
Manufacturer:
Description:
Audio Amplifiers 10V-14.6V 2-wire 2 Output Audio Prcsr
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet