MC-7834-KC-AZ

870 MHz GaAs CATV 20 dB PUSH-PULL AMPLIFIER
MC-7834-KC
OUTLINE DIMENSIONS (Units in mm)
PACKAGE OUTLINE H02
FEATURES
GaAs ACTIVE DEVICES
LOW DISTORTION
HIGH LINEAR GAIN:
MC-7834-KC - GL = 21 dB MIN at f = 870 MHz
LOW RETURN LOSS
LOW GAIN CHANGE OVER TEMPERATURE
SPECIFIED FOR 79, 110, and 132 CHANNELS
PERFORMANCE
HIGH RELIABILITY AND RUGGEDNESS:
Withstands environmental extremes as well as Silicon
devices (Surge, ESD, Etc.)
DESCRIPTION
The MC-7834-KC is a GaAs Multi-Chip Module designed
for use as input stages in CATV applications up to 870 MH
z.
Because this unit is a GaAs device, it has low distortion, low
noise figure, and low return loss across the entire frequency
band. The MC-7834-KC is similar to the standard push-pull
devices, but with the higher current allows better distortion
performance, especially X-Mod.
Like the previous generation of products, these devices sur-
vive such hazards as surge and ESD as well as their silicon
competitors, but deliver superior performance with low DC
current required.
All devices are assembled and tested using fully automated
equipment to maximize consistency in part to part perfor-
mance, and reliability is assured by stringent quality and
process control procedures. These parts come in industry
compatible hybrid packages.
V
DD
91
In Out
Gnd
2 3 7 8
2.54
±0.38
21.5 MAX
12.9 MAX
6-32 unc 2B
2.54
±0.25
1 2 3 5 789
4.19
±0.13
14.85 MAX
4.25
+ 0.25
- 0.35
4.0±0.25
5
10.75±0.25
27.5 MAX
38.1±0.25
45.08 MAX
0.51±0.050
53.026.2
3.2 MAX
A
0.38.. A
25.4±0.25
19.05±0.38
8.1 MAX
2.5
6.3
±0.05
APPLICATIONS
CATV HEADEND SYSTEMS
CATV OPTICAL NODES
CATV DISTRIBUTION AMPS
PART NUMBER MC-7834-KC
TEST CONDITIONS
SYMBOLS CHARACTERISTICS UNITS MIN TYP MAX
BW Frequency Range MHz 50 870
G
L Linear Gain dB 20.0 21.0 f = 870 MHz
S Gain Slope dB 0.2 1.0 f = 40 to 870 MHz
Gf Gain Flatness dB 0.7 40 to 870 MHz; Peak to Valley
NF
Noise Figure 1
Noise Figure 2
dB 6.5 f = 50 MHz
7.0 f = 870 MHz
RL Input/Output Return Loss dB 20.0 40 to 160MHz
19.0 160 to 320 MHz
17.5 320 to 640 MHz
16.0 640 to 870 MHz
IDD Operating Current mA 180 325 RF OFF
CTB Composite Triple Beat dBc -59 f = 40 to 870 MHz; 110 Channels,
V
OUT = 44 dBmV, Flat
XMod Cross Modulation dBc -52
CSO Composite Second Order dBc -59
ELECTRICAL CHARACTERISTICS (TA = 30±5 °C, VDD = 24 V, ZS = ZL = 75 Ω)
Date Published January 2007
MC-7834-KC
ABSOLUTE
MAXIMUM RATINGS
1
(TCASE= 30 °C)
SYMBOLS PARAMETERS UNITS RATINGS
V
DD Supply Voltage V 30
V
I Input Voltage
2
dBmV 65
T
C Operating Case Temperature °C -30 to +100
T
STG Storage Temperature °C -40 to +100
Note:
1. Operation in excess of any one of these parameters may result in
permanent damage.
2. Maximum single channel power applied to the input for 1 minute
with no measurable degradation in performance.
SYMBOLS PARAMETERS UNITS MIN TYP MAX
V
DD Supply Voltage V
MC-7834-KC 23.5 24.0 24.5
V
i Input Voltage
1
dBmV
MC-7834-KC 21.0 27.5
T
C Operating Case °C
Temperature
MC-7834-KC -30 +25 +85
RECOMMENDED
OPERATING CONDITIONS
(Zs = ZL = 75Ω)
Note:
1. Test Conditions: 110 Channels, Flat
PART NUMBER PACKAGE QUANTITY
MC-7834-KC-AZ 7-pin special with heatsink 25 pcs max/ Tray
(Pb-Free)
ORDERING INFORMATION
1. The space between PC board and root of the lead should be kept
more than 1 mm to prevent undesired stress on the lead and also
should be kept less than 4 mm to prevent undesired parasitic
inductance.
Recommended space is 2.0 to 3.0 mm typical.
2. Recommended torque strength of the screw is 59 to 78 Ncm.
3. Form the ground pattern as wide as possible to minimize ground
impedance. (to prevent undesired oscillation)
All the ground pins must be connected together with wide ground
pattern to decrease impedance difference.
NOTES ON CORRECT USE
This product should be soldered in the following recommended
conditions. Other soldering methods and conditions than the recom-
mended conditions are to be consulted with our sales representa-
tives.
RECOMMENDED SOLDERING CONDITIONS
Soldering Soldering Condition
Method Conditions Symbol
Pin Part Heating Pin area temperature: less
than 260°C
1
Hour: Within 2 sec./pin
Note.
1. The point of pin part heating must be kept at a distance of more
than 1.2 mm from the root of lead.
The information in this document is subject to change without notice. Before using this document, please confirm
that this is the latest version.

MC-7834-KC-AZ

Mfr. #:
Manufacturer:
CEL
Description:
RF Amplifier 870 MHz GaAs CATV Push-Pull
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union