March 2000 3 MIC2536
MIC2536 Micrel
Electrical Characteristics
V
IN
= +5V; T
A
= 25°C, bold values indicate –40°C ≤ T
A
≤ +85°C; unless noted
Parameter Condition Min Typ Max Units
Supply Current both switches off, OUTA–B = open, Note 4 0.75 5 µA
both switches on, OUTA–B = open, Note 4 60 100 µA
Enable Input Threshold low-to-high transition, Note 4 1.7 2.4 V
high-to-low transition, Note 4 0.8 1.5 V
Enable Input Current V
EN
= 0V to 5.5V 0.01 1 µA
Enable Input Capacitance Note 5 1pF
Switch Resistance single switch, I
OUT
= 100mA 400 700 mΩ
Output Turn-On Delay, t
ON
R
L
= 50Ω, C
L
= 1µF 1.5 ms
Output Turn-On Rise Time, t
R
R
L
= 50Ω, C
L
= 1µF 1.4 ms
Output Turnoff Delay, t
OFF
R
L
= 50Ω, C
L
= 1µF 130 µs
Output Turnoff Fall Time, t
F
R
L
= 50Ω, C
L
= 1µF 115 µs
Output Leakage Current each output (switch off) 1 10 µA
Current Limit Threshold ramped load applied to enable output 500 mA
Short Circuit Current Limit each output (enabled into load), V
OUT
= 0V 150 275 400 mA
Current Limit Response V
OUT
= 0V to I
OUT
= I
LIMIT
(short applied to output), Note 5 10 µs
Flag Response Delay, t
D
V
IN
= 5V, apply V
OUT
= 0V until FLG low 5 13 20 ms
V
IN
= 3.3V, apply V
OUT
= 0V until FLG low 13 ms
Overtemperature Shutdown T
J
increasing, Note 5 135 °C
Threshold T
J
decreasing, Note 5 125 °C
Error Flag Output Resistance V
IN
= 5V, I
L
= 10mA 10 20 Ω
V
IN
= 3.3V, I
L
= 10mA 15 30 Ω
Error Flag Off Current V
FLAG
= 5V 0.01 1 µA
Note 1. Exceeding the absolute maximum rating may damage the device.
Note 2. The device is not guaranteed to function outside its operating rating.
Note 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF.
Note 4. Off is ≤ 0.8V and on is ≥ 2.4V for the MIC2536-1. Off is ≥ 2.4V and on is ≤ 0.8V for the MIC2536-2. The enable input has approximately
200mV of hysteresis.
Note 5. Guaranteed by design. Not production tested.
Absolute Maximum Ratings (Note 1)
Supply Voltage (V
IN
) .....................................................+6V
Fault Flag Voltage (V
FLG
)..............................................+6V
Fault Flag Current (I
FLG
) ............................................25mA
Output Voltage (V
OUT
) ..................................................+6V
Output Current (I
OUT
) ............................... Internally Limited
Control Input (V
EN
)................................... –0.3V to V
IN
+2V
Storage Temperature (T
S
) ....................... –65°C to +150°C
Lead Temperature (Soldering 5 sec.) ....................... 260°C
ESD Rating, Note 3 ...................................................... 1kV
Operating Ratings (Note 2)
Supply Voltage (V
IN
) ................................... +2.7V to +5.5V
Ambient Operating Temperature (T
A
) ........ –40°C to +85°C
Thermal Resistance
SOP (θ
JA
) ..........................................................160°C/W
MSOP (θ
JA
) .......................................................206°C/W
