OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

GS100101

P1-P2
www.cherryswitches.com
Page 1 of 2, Last update 2015-12-15, Specifications subject to change without notice.
Gear Tooth Speed Sensors
GS1001 – GS1002 Sensors
Hall Effect gear tooth speed sensor with
adjustable stainless steel housing
Description
The GS1001-GS1002 series gear tooth speed sensors are Hall Effect devices designed for use in applications where ferrous
edge detection/near zero speed sensing is needed. They provide a sinking current output.
Features
Typical Applications
• From near zero speed up to 15 kHz sensing capability
• 10 bit dynamic threshold direction offers:
- Automatically adjusting magnetic range
- Self-compensating to target geometry
• Compatible with unregulated power supply
• RoHS compliant
• IP67
• Typical air gap of 1.5 mm*
• Speedometers
• Anti-lock braking systems
• Exercise equipment
• CNC machine tools
Environmental Specifications
Vibration
Sinusoidal, 15 g max from 40 Hz to 2 kHz
Mechanical Shock Resistance
Maximum Speed Detection
15 kHz
Operating
Temperature (GS100101, GS100201)
-
40
°
C to 105
⁰
C (
-
40
⁰
F to 221
⁰
F)
Operating Temperature (GS100102, GS100202)
-
40
°
C to 125
⁰
C (
-
40
⁰
F to 257
⁰
F)
Storage Temperature
-
40
°
C to 125
⁰
C (
-
40
⁰
F to 257
⁰
F)
Ingress Protection
IP67
Electrical
Specifications
Operating Supply Voltage
5 to 24 VDC
Maximum Input Voltage
30 VDC
Maximum Reverse Voltage
24 VDC
Supply Current
3 mA typ., 6 mA max
Output Sink Current
20 mA max
Recommended Pull
-
Up Resistor
See chart
Mechanical Specifications
Housing Material
303 Stainless Steel
Maximum Installation Torque Limit
5.65 Nm (50 in lb) on threads
Operating Air Gap / Sensing Distance*
1.5 mm (0.06")
* With recommended target type; see drawing
Sensor Orientation
Not sensitive
Products
N
umber
Thread
Shielded Cable with Drain
Connector
GS1001
01
M12
-
1
12 mm, 4
-
pin circular mating connector, type IEC 60947
-
5
-
2
GS1001
0
2
M12
-
1
22 AWG x 1 m
GS1002
01
M18
-
1
12 mm, 4
-
pin circular mating connector, type IEC 60947
-
5
-
2
GS1002
0
2
M18
-
1
22 AWG
x 1 m
www.cherryswitches.com
Page 2 of 2, Last update 2015-12-15, Specifications subject to change without notice.
Note: An external pull-up resistor is required, the value of which is dependent on the supply voltage. The resistor should be
connected between the output and Vcc. Refer to the wiring diagram for lead colors or pin numbering as applicable.
Recommended External Pull
-
Up Resistor
Volts DC
5
9
12
15
24
Ohms
1k
1.
8k
2
.
4k
3k
3k
Open Collector Sinking Block Diagram
Dimensions mm (inches)
GS100101 GS100102
Installation
For best results, we recommend targets made from low carbon cold rolled
steel. Other factors that influence sensor performance include gear tooth
height and width, space between the teeth, shape of the teeth and thickness
of the target. As a general guideline, consider a target with minimum
parameters as shown below. Note that smaller dimensions may work, but
testing for the application is required.
Tooth Height Tooth Width Distance
between Teeth
Target Thickness
5.0 mm (.200") 2.5 mm (.100") 10 mm (.400") 6.35 mm (.250")
G
S100201
G
S1002
02
P1-P2

GS100101

Mfr. #:
Buy GS100101
Manufacturer:
CHERRY
Description:
Motion & Position Sensors Speed Sensors HALL EFFCT 6mA 24VDC M12-1 12mm CircCnct
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet