Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
Radial Lead
NPCAP
TM
-PSGSeries
・
Super low ESR, high ripple current capability
・
Added 35V
・
Endurance: 15,000 to 20,000 hours at 105
℃
・
Rated voltage : 16 to 35V
dc
・
RoHS2 Compliant
・
Halogen Free
◆
SPECIFICATIONS
Items Characteristics
Category
Temperature Range
-55 to +105
℃
Rated Voltage
16 to 35V
dc
Capacitance Tolerance
±
20% (M) (at 20
℃
, 120Hz)
Surge Voltage
Rated voltage(V)
×
1.15 (at 105
℃
)
Leakage Current
*Note
I=0.2CV or 500μA, whichever is greater
Where, I : Leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V) (at 20
℃
after 2 minutes)
Dissipation Factor
(tan
δ
)
0.12 max.
(at 20
℃
, 120Hz)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Z(-25
℃
)/Z(+20
℃
)
≦
1.15
Z(-55
℃
)/Z(+20
℃
)
≦
1.25
(at 100kHz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after the rated voltage is applied for 20,000 hours
(20 to 35V : 15,000 hours) at 105
℃
.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
150% of the initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Bias Humidity Test
The following specifications shall be satisfied when the capacitors are restored to 20
℃
after subjecting them to DC voltage at 60
℃
,
90 to 95% RH for 1,000 hours.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
The initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Surge Voltage Test
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105
℃
for 30 seconds
through a protective resistor(R=1k
Ω
) and discharge for 5 minutes 30 seconds.
Appearance No significant damage
Capacitance change
≦±
20% of the initial value
D.F. (tan
δ
)
≦
The initial specified value
ESR
≦
150% of the initial specified value
Leakage current
≦
The initial specified value
Failure Rate
0.5% per 1,000 hours maximum (Confidence level 60% at 105
℃
)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆
DIMENSIONS [mm]
Size code
φ
D
φ
d
F
φ
D'
L'
0.45
6.3
2.5
8.0
0.6
3.5
HB5H08H06F08F05 H16 H20 JB5 J16 J20
10.0
5.0
L+1.5max.L+1.0max.
(
Note1
)
φ
D+0.5max.
Coated Case
L'
15min. 4min.
φ
D'
φ
d
F
±
0.5
F
±
0.5
Coated Case
L'
15min. 4min.
φ
D'
φ
d
F05,F08,H06,H08
HB5,H16,H20,JB5,J16,J20
●
Note1 : L+1.2 max. for 16V270μF (Rated ripple current 5,080mArms).
Upgrade!
Downsized
PSG
PSF P2-40
◆
MARKING
G
6D6
150
16
V
2-36
CAT. No. E1001R
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
