OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

TSOP58238

P1-P3P4-P6P7-P7
TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
Rev. 1.5, 22-Jul-16
1
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
IR Receiver Modules for Remote Control Systems
MECHANICAL DATA
Pinning for TSOP582.., TSOP584..:
1 = OUT, 2 = GND, 3 = V
S
FEATURES
• Improved immunity against HF and RF noise
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.5 V to 5.5 V
• Improved immunity against optical noise
• Insensitive to supply voltage ripple and noise
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
DESCRIPTION
These products are miniaturized IR receiver modules for
infrared remote control systems. A PIN diode and a
preamplifier are assembled on a leadframe, the epoxy
package contains an IR filter.
The demodulated output signal can be directly connected to
a microprocessor for decoding.
The TSOP584.. series devices are optimized to suppress
almost all spurious pulses from Wi-Fi and CFL sources.
They may suppress some data signals if continuously
transmitted.
The TSOP582.. series devices are provided primarily for
compatibility with old AGC2 designs. New designs should
prefer the TSOP584.. series containing the newer AGC4.
These components have not been qualified according to
automotive specifications.
19026
PARTS TABLE
AGC
LEGACY, FOR LONG BURST REMOTE CONTROLS
(AGC2)
RECOMMENDED FOR LONG
BURST CODES (AGC4)
Carrier
frequency
30 kHz TSOP58230 TSOP58430
33 kHz TSOP58233 TSOP58433
36 kHz TSOP58236 TSOP58436
(1)(2)(3)
38 kHz TSOP58238 TSOP58438
(4)(5)
40 kHz TSOP58240 TSOP58440
56 kHz TSOP58256 TSOP58456
(6)(7)
Package Minicast
Pinning 1 = OUT, 2 = GND, 3 = V
S
Dimensions (mm) 5.0 W x 6.95 H x 4.8 D
Mounting Leaded
Application Remote control
Best remote control code
(1)
RC-5
(2)
RC-6
(3)
Panasonic
(4)
NEC
(5)
Sharp
(6)
r-step
(7)
Thomson RCA
TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
Rev. 1.5, 22-Jul-16
2
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
BLOCK DIAGRAM APPLICATION CIRCUIT
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
TYPICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
33 kΩ
2
3
1
Demo-
pass
AGCInput
PIN
Band
dulator
Control circuit
16833_14
C
1
IR receiver
GND
Circuit
μC
R
1
+ V
S
GND
Transmitter
with
TSALxxxx
V
S
V
O
17170-11
OUT
R
1
and C
1
recommended to reduce supply ripple for V
S
< 2.8 V
ABSOLUTE MAXIMUM RATINGS
PARAMETER TEST CONDITION SYMBOL VALUE UNIT
Supply voltage V
S
-0.3 to +6 V
Supply current I
S
5mA
Output voltage V
O
-0.3 to 5.5 V
Voltage at output to supply V
S
- V
O
-0.3 to (V
S
+ 0.3) V
Output current I
O
5mA
Junction temperature T
j
100 °C
Storage temperature range T
stg
-25 to +85 °C
Operating temperature range T
amb
-25 to +85 °C
Power consumption T
amb
≤ 85 °C P
tot
10 mW
Soldering temperature t ≤ 10 s, 1 mm from case T
sd
260 °C
ELECTRICAL AND OPTICAL CHARACTERISTICS (T
amb
= 25 °C, unless otherwise specified)
PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT
Supply voltage V
S
2.5 - 5.5 V
Supply current
V
S
= 5 V, E
v
= 0 I
SD
0.55 0.7 0.9 mA
E
v
= 40 klx, sunlight I
SH
-0.8-mA
Transmission distance
E
v
= 0, IR diode TSAL6200,
I
F
= 250 mA, test signal see Fig. 1
d-40-m
Output voltage low I
OSL
= 0.5 mA, E
e
= 0.7 mW/m
2
, test signal see Fig. 1 V
OSL
- - 100 mV
Minimum irradiance
Pulse width tolerance:
t
pi
- 5/f
o
< t
po
< t
pi
+ 6/f
o,
test signal see Fig. 1
E
e min.
-0.20.4mW/m
2
Maximum irradiance t
pi
- 5/f
o
< t
po
< t
pi
+ 6/f
o
, test signal see Fig. 1 E
e max.
50 - - W/m
2
Directivity Angle of half transmission distance ϕ
1/2
-± 45-deg
16110
E
e
T
t
pi
*
t
* t
pi
10/f
0
is recommended for optimal function
V
O
V
OH
V
OL
t
Optical Test Signal
(IR diode TSAL6200, I
F
= 0.4 A, 30 pulses, f = f
0
, t = 10 ms)
Output Signal
t
d
1)
t
po
2)
1)
7/f
0
< t
d
< 15/f
0
2)
t
pi
- 5/f
0
< t
po
< t
pi
+ 6/f
0
1.0
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0.1 1 10 10
2
10
3
10
4
E
e
- Irradiance (mW/m
2
)
t
po
- Output Pulse Width (ms)
Input Burst Length
Output Pulse Width
λ = 950 nm,
Optical Test Signal, Fig.1
0
0.1
TSOP582.., TSOP584..
www.vishay.com
Vishay Semiconductors
Rev. 1.5, 22-Jul-16
3
Document Number: 82461
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Fig. 3 - Output Function
Fig. 4 - Output Pulse Diagram
Fig. 5 - Frequency Dependence of Responsivity
Fig. 6 - Sensitivity in Bright Ambient
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
Fig. 8 - Sensitivity vs. Electric Field Disturbances
E
e
t
V
O
V
OH
V
OL
t
600 µs 600 µs
t = 60 ms
t
on
t
off
94 8134
Optical Test Signal
Output Signal, (see fig. 4)
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.1 1 10 100 1000 10 000
t
on
, t
off
- Output Pulse Width (ms)
E
e
- Irradiance (mW/m
2
)
t
on
t
off
λ = 950 nm,
optical test signal, g. 1
0.0
0.2
0.4
0.6
0.8
1.0
1.2
0.7 0.9 1.1 1.3
f/f
0
- Relative Frequency
16925
f = f
0
± 5 %
Δf(3 dB) = f
0
/10
E
e min.
/E
e
- Relative Responsivity
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0.01 0.1 1 10 100
E
e
- Ambient DC Irradiance (W/m
2
)
E
e min.
- Threshold Irradiance (mW/m
2
)
Correlation with ambient light sources:
10 W/m
2
= 1.4 klx (std. illum. A, T = 2855 K)
10 W/m
2
= 8.2 klx (daylight, T = 5900 K)
Wavelength of ambient
illumination:
λ
= 950 nm
4.5
5.0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1 10 100 1000
ΔV
s
RMS
- AC Voltage on DC Supply Voltage (mV)
E
e min.
- Threshold Irradiance (mW/m
2
)
f = f
0
f = 20 kHz
f = 30 kHz
f = 100 Hz
f = 10 kHz
0
50
100
150
200
250
300
350
400
450
500
0 500 1000 1500 2000 2500 3000
f - EMI Frequency (MHz)
E - Max. Field Strength (V/m)
20747
P1-P3P4-P6P7-P7

TSOP58238

Mfr. #:
Buy TSOP58238
Manufacturer:
Vishay Semiconductors
Description:
Infrared Receivers Minicast 38kHz AGC2
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet