LTC2460/LTC2462
8
24602fa
applicaTions inForMaTion
mode during the DATA INPUT/OUTPUT state. Once the
next conversion is complete, the SLEEP state is entered
and power is reduced to less than 2μA. The reference is
powered up once CS is brought low. The reference startup
time is 12ms (if the reference and compensation capacitor
values are both 0.1μF).
Upon entering the DATA INPUT/OUTPUT state, SDO outputs
the sign (D15) of the conversion result. During this state,
the ADC shifts the conversion result serially through the
SDO output pin under the control of the SCK input pin.
There is no latency in generating this data and the result
corresponds to the last completed conversion. A new bit
of data appears at the SDO pin following each falling edge
detected at the SCK input pin and appears from MSB to
LSB. The user can reliably latch this data on every rising
edge of the external serial clock signal driving the SCK pin.
During the DATA INPUT/OUTPUT state, the LTC2460/
LTC2462 can be programmed to SLEEP or NAP (default)
following the next conversion cycle. Data is shifted into the
device through the SDI pin on the rising edge of SCK. The
input word is 4 bits. If the first bit EN1 = 1 and the second
bit EN2 = 0 the device is enabled for programming. The
following two bits (SPD and SLP) will be written into the
device. SPD (only used for the LTC2460) to select the 60Hz
output rate, no offset calibration mode (SPD = 0, default).
Set SPD = 1 for 30Hz mode with offset calibration. SPD
is ignored for the LTC2462. The next bit (SLP) enables
the sleep or nap mode. If SLP = 0 (default) the reference
remains powered up at the end of the next conversion
cycle. If SLP = 1, the reference powers down following
the next conversion cycle. The remaining 12
SDI
input
bits are ignored (don’t care).
SDI may also be tied directly to GND or V
DD
in order to
simplify the user interface. In the case of the LTC2460,
the 60Hz output rate is selected if SDI is tied low and
the 30Hz output rate is selected if SDI is tied to V
DD
. The
LTC2462 output rate is always 60Hz independent of SDI
or SPD. The reference sleep mode is disabled for both
the LTC2460 and LTC2462 if SDI is tied to GND or V
DD
.
The DATA INPUT/OUTPUT state concludes in one of two
different ways. First, the DATA INPUT/OUTPUT state opera-
tion is completed once all 16 data bits have been shifted
out and the clock then goes low. This corresponds to the
16
th
falling edge of SCK. Second, the DATA INPUT/OUT-
PUT state can be aborted at any time by a LOW-to-HIGH
transition on the CS input. Following either one of these
two actions, the LTC2460/LTC2462 will enter the CONVERT
state and initiate a new conversion cycle.
Power-Up Sequence
When the power supply voltage (V
CC
) applied to the con-
verter is below approximately 2.1V, the ADC performs a
power-on reset. This feature guarantees the integrity of
the conversion result.
When V
CC
rises above this critical threshold, the converter
generates an internal power-on reset (POR) signal for
approximately 0.5ms. The POR signal clears all internal
registers. Following the POR signal, the LTC2460/LTC2462
start a conversion cycle and follow the succession of states
shown in Figure 2. The reference startup time following a
POR is 12ms (C
COMP
= C
REFOUT
= 0.1μF). The first conver-
sion following powerup will be invalid since the reference
voltage has not completely settled. The first conversion
following power up can be discarded using the data abort
command or simply read and ignored. The following con-
versions are accurate to the device specifications.
Ease of Use
The LTC2460/LTC2462 data output has no latency, filter
settling delay or redundant results associated with the
conversion cycle. There is a one-to-one correspondence
Figure 3. Output Code vs V
IN
+
with V
IN
–
= 0 (LTC2462)
V
IN
+
/V
REF
+
–0.001
OUTPUT CODE
4
12
0.001
24602 F03
–4
–12
0
8
16
–8
–16
–20
–0.005
0
0.005
0.0015
SIGNALS
BELOW
GND