REV. D
–2–
CMP04–SPECIFICATIONS
Parameter Symbol Conditions Min Typ Max Unit
Input Offset Voltage V
OS
R
S
= 0 Ω, R
L
= 5.1 kΩ, V
O
= 1.4 V
1
0.4 1 mV
Input Offset Current I
OS
I
IN
(+) – I
IN
(–), R
L
= 5.1 kΩ, V
O
= 1.4 V 2 10 nA
Input Bias Current I
B
I
IN
(+) or I
IN
(–) 25 100 nA
Voltage Gain A
V
R
L
≥ 15 kΩ, V+ = 15 V
2
80 200 V/mV
Large Signal Response Time t
r
V
IN
= TTL Logic Swing, V
REF
= 1.4 V
3
V
RL
= 5 V, R
L
= 5.1 kΩ 300 ns
Small Signal Response Time t
r
V
IN
= 100 mV Step
3
, 5 mV Overdrive
V
RL
= 5 V, R
L
= 5.1 kΩ 1.3 µs
Input Voltage Range CMVR Note 4 0 V+ – 1.5 V
Common-Mode Rejection Ratio CMRR Notes 2, 5 80 100 dB
Power Supply Rejection Ratio PSRR V+ = 5 V to 18 V
2
80 100 dB
Saturation Voltage V
OL
V
IN
(–) ≥ 1 V, V
IN
(+) = 0, I
SINK
≤ 4 mA 250 400 mV
Output Sink Current I
SINK
V
IN
(–) ≥ 1 V, V
IN
(+) = 0, V
O
≤ 1.5 V 6 16 mA
Output Leakage Current I
LEAK
V
IN
(+) ≥ 1 V, V
IN
(–) = 0, V
O
= 30 V 0.1 100 nA
Supply Current I+ R
L
=
∞
, All Comps V+ = 30 V 0.8 2.0 mA
NOTES
1
At output switch point, V
O
= 1.4 V, R
S
= 0 Ω with V+ from 5 V, and over the full input common-mode range (0 V to V+ – 1.5 V).
2
Guaranteed by design.
3
Sample tested.
4
The input common-mode voltage or input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of the common-mode voltage range
is V+ – 1.5 V, but either or both inputs can go to 30 V without damage.
5
R
L
≥ 15 kΩ, V+ = 15 V, V
CM
= 1.5 V to 13.5 V.
Specifications subject to change without notice.
ELECTRICAL CHARACTERISTICS
(@ V+ = 5 V, T
A
= 25ⴗC, unless otherwise noted.)
ABSOLUTE MAXIMUM RATINGS
1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . +36 V or ± 18 V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . 36 V dc
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +36 V
Operating Temperature Range
CMP04FS . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Junction Temperature (T
J
) . . . . . . . . . . . . . –65°C to +150°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Input Current (V
IN
< –3.0 V) . . . . . . . . . . . . . . . . . . . 50 mA
Output Short Circuit to GND . . . . . . . . . . . . . . . . Continuous
Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . . 300°C
Package Type
JA
2
JC
Unit
14-Lead SOIC 120 36 °C/W
NOTES
1
Absolute maximum ratings apply to both DICE and packaged parts, unless
otherwise noted. Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress rating only; functional
operation of the device at these or any other conditions above those listed in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2
θ
JA
is specified for worst-case mounting conditions, i.e., θ
JA
is specified for device
soldered to printed circuit board for SOIC package.
ORDERING GUIDE
T
A
= 25ⴗC Temperature Package Package
Model V
OS
Ranges Descriptions Options
CMP04FS 1 mV –40°C to +85°C 14-Lead SOIC R-14
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the CMP04 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
