74LVC4066_Q100 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2012. All rights reserved.
Product data sheet Rev. 1 — 7 August 2012 5 of 23
NXP Semiconductors
74LVC4066-Q100
Quad bilateral switch
8. Recommended operating conditions
[1] To avoid sinking GND current from terminal nZ when switch current flows in terminal nY, the voltage drop across the bidirectional switch
must not exceed 0.4 V. If the switch current flows into terminal nZ, no GND current flows from terminal nY. In this case, there is no limit
for the voltage drop across the switch.
[2] Applies to control signal levels.
9. Static characteristics
Table 5. Recommended operating conditions
Symbol Parameter Conditions Min Typ Max Unit
V
CC
supply voltage 1.65 - 5.5 V
V
I
input voltage 0 - 5.5 V
V
SW
switch voltage
[1]
0- V
CC
V
T
amb
ambient temperature 40 - +125 C
t/V input transition rise and fall rate V
CC
=1.65Vto2.7V
[2]
--20ns/V
V
CC
= 2.7 V to 5.5 V
[2]
--10ns/V
Table 6. Static characteristics
At recommended operating conditions voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions 40 C to +85 C 40 C to +125 C Unit
Min Typ
[1]
Max Min Max
V
IH
HIGH-level
input voltage
V
CC
= 1.65 V to 1.95 V 0.65V
CC
- - 0.65V
CC
-V
V
CC
= 2.3 V to 2.7 V 1.7 - - 1.7 - V
V
CC
= 2.7 V to 3.6 V 2.0 - - 2.0 - V
V
CC
= 4.5 V to 5.5 V 0.7V
CC
- - 0.7V
CC
-V
V
IL
LOW-level
input voltage
V
CC
= 1.65 V to 1.95 V - - 0.35V
CC
-0.35V
CC
V
V
CC
= 2.3 V to 2.7 V - - 0.7 - 0.7 V
V
CC
= 2.7 V to 3.6 V - - 0.8 - 0.8 V
V
CC
= 4.5 V to 5.5 V - - 0.3V
CC
-0.3V
CC
V
I
I
input leakage
current
pin nE; V
CC
= 5.5 V;
V
I
=5.5VorGND
[2]
- 0.1 5-20 A
I
S(OFF)
OFF-state
leakage
current
V
SW
= V
CC
GND; V
CC
=5.5 V;
see Figure 6
[2]
- 0.1 5-20 A
I
S(ON)
ON-state
leakage
current
V
SW
= V
CC
GND; V
CC
=5.5 V;
see Figure 7
[2]
- 0.1 5-20 A
I
CC
supply current V
I
=V
CC
or GND; V
SW
=GNDor
V
CC
; V
CC
= 5.5 V
[2]
-0.110 - 40A
I
CC
additional
supply current
pin nE; V
I
=V
CC
0.6 V; V
CC
= 5.5 V;
V
SW
=GNDor V
CC
[2]
- 5 500 - 5000 A
