DLP0RSN900HP2D Datasheet DLP0RSN900HP2D | P1-P3

Spec No. :JEFL243E-0023-01 P 1/9

MURATA MFG.CO., LTD

Reference Only

Chip Common Mode Choke Coil

DLP0RSN□□□HP2□ Reference Specification

1. Scope

This reference specification applies to Chip Common Mode Choke Coil DLP0RSN Series.

2. Part Numbering

(ex.) DL P 0R S N 900 H P 2 D

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)

(1) Chip Common Mode Choke Coil

(2) Structure (P : Film Type)

(3) Dimension (L×W)

(4) Type

(5) Category

３．Rating

Customer

Part Number

MURATA

Part Number

Common Mode

Impedance

(Ω)

at 100MHz

(Under Standard

Testing Condition)

Rated

Current

(mA)

Rated

Voltage

(V(DC))

Withstandin

Voltage

(V(DC))

Resistance

(Rdc)

(Ω)

Insulation

Resistance

(I.R.)

(Ω)

DLP0RSN900HP2D

90±35%

50 5

12.5

3.0±30%

100M

min.

DLP0RSN900HP2B

DLP0RSN650HP2D

65±35% 50 5 3.0±30%

100M

min.

DLP0RSN650HP2B

Operating Temperature : -40 to +85°C (Self- temperature rise is not included) Storage Temperature : -40 to +85°C

4. Standard Testing Conditions

Unless otherwise specified> <In case of doubt>

Temperature : Ordinary Temperature 15 to 35°C Temperature : 20 ± 2°C

Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH)

Atmospheric Pressure : 86 to106kPa

5.Style and Dimensions

■ Equivalent Circuits

部品質量（参考値）

0.2mg

6.Marking

No Marking.

0.25 max

(Top View)

(Bottom View)

(Side View)

0.30±0.05

(0.075)

0.45±0.05

(1) (2)

(3)(4)

:Electrode

(in : mm)

(0.15)

(6) Resonant Frequency

(7)Circuit H : Characteristic Impedance 100Ω system

(8) Features

(9) Number of Line

(10) Packaging Code D : Taping / B : Bulk

(1) (2)

(4) (3)

Spec No. :JEFL243E-0023-01 P 2/9

MURATA MFG.CO., LTD

Reference Only

7. Electrical Performance

No. Item Specification Test Method

7.1 Common Mode

Impedance

Meet item 3. Measuring Frequency : 100±1MHz (ref.item 10.)

Measuring Equipment : Agilent 4291A or the equivalents

(In case of doubt in standard condition, the heat

treatment(200°C, about 10 min) shall be applied.

7.2 Withstanding

Voltage

Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage

Time : 1 to 5 s

Charge Current : 1 mA max.(ref.item 10.)

7.3 DC Resistance

(Rdc)

Meet item 3.

Measuring current : 10mA max. (ref.item 10.)

7.4 Insulation

Resistance (I.R.)

Measuring voltage : Rated Voltage

Measuring time : 1 min max. (ref.item 10.)

7.5

Rated Current

Self- temperature rise shall be limited

to 25℃ max.

The rated current is applies.

8.Mechanical Performance

No. Item Specification Test Method

8.1 Appearance and

Dimensions

Meet item 5.

Visual Inspection and measured with Slide Calipers.

8.2 Solderability The electrodes shall be at least

95% covered with new solder

coating.

Flux : Ethanol solution of rosin,25(wt)%

Pre-Heating : 150±10°C, 60s

Solder : Sn-3.0Ag-0.5Cu

Solder Temperature : 230+0--5°C

Immersion Time : 3±1s

Immersion and emersion rates : 25 mm / s

8.3 Resistance to

Soldering Heat

The electrodes shall be at least

84% covered with new solder

coating.

Meet Table 1.

Tabl e 1

Flux : Ethanol solution of rosin,25(wt)%

Pre-Heating : 150±10°C, 60s

Solder : Sn-3.0Ag-0.5Cu

Solder Temperature : 270±5°C

Immersion Time : 10±1s

Immersion and emersion rates : 25 mm / s

Immersion depth: 2~2.5mm

The Number of Times : 3 times

Then measured arter exposure in the room condition

for 4 to 48 hours.

8.4 Drop

Meet Table 1.

It shall be dropped on concrete or steel board.

Method : free fall

Height : 1m

The Number of Times : 10 times

8.5 Vibration It shall be soldered on the substrate.

Oscillation Frequency : 10 to 2000 for 20 min

Total amplitude : 3.0 mm

Testing Time : A period of 4 hours in each of 3 mutually

perpendicular directions.

Appearance No damaged

Common Mode

Impedance

Change

within ± 20%

I.R. 100MΩ min.

DC Resistance

Change

within ± 30%

Spec No. :JEFL243E-0023-01 P 3/9

MURATA MFG.CO., LTD

Reference Only

No.

Item Specification Test Method

8.6 Bending

Strength

Meet Table 2.

Table 2

Substrate : (t =0.8 mm).

Deflection : 2 mm

Speed of Applying Force : 1.0 mm / s

Keeping time : 5 s

9.Environmental Performance (Products shall be solderd on the glass-epoxy substrate)

No. Item Specification Test Method

9.1

Temperature

Cycle

Meet Table 1.

1 Cycle

Step 1 -40°C(+0°C,-3°C) / 30(+3,-0) min

Step 2 Ordinary Temp. / within 3 min

Step 3 +85(+3°C,-0°C) / 30(+3,-0) min

Step 4 Ordinary Temp. / within 3 min

Total of 100 cycles.

Then measured after exposure in the room condition for

4 to 48 hours.

9.2

Humidity Temperature : 40±2°C

Humidity : 90 to 95 % (RH)

Time : 1000 hours(+48 hours,-0 hours)

Then measured after exposure in the room condition for

4 to 48 hours.

9.3

Heat life Temperature : 85±2°C

Test Voltage : 2 times for Rated Voltage

Time : 1000 hours(+48 hours,-0 hours)

Then measured after exposure in the room condition for

4 to 48 hours. (ref. Item 10.)

9.4

Cold Resistance Temperature : -40± 2°C

Time : 1000 hours(+48 hours,-0 hours)

Then measured after exposure in the room condition for

4 to 48 hours.

10. Terminal to be Tested.

When measuring and suppling the voltage,the following terminal is applied.

No. Item Terminal to be Tested

10.1 Common Mode

Impedance

10.2

Withstanding Voltage

Insulation Resistance

Heat Life

10.3 DC Resistance

ＩＮ

ＯＵＴ

ＩＮ

ＯＵＴ

ＩＮ

ＯＵＴ

ＩＮ

ＯＵＴ

Appearance No damaged

DC Resistance

Change

within ± 30%

R230

Deflection

Product

Pressure jig

P1-P3 P4-P6 P7-P9

DLP0RSN900HP2D

Mfr. #:

Buy DLP0RSN900HP2D

Manufacturer:

Description:

CMC 50MA 90 OHM SMD

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

DLP0RSN900HP2D