1996-2012 Microchip Technology Inc. DS21130F-page 1
93AA76/86
Features:
Single supply operation down to 1.8V
Low-power CMOS technology:
- 1 mA active current typical
-5 A standby current (typical) at 3.0V
ORG pin selectable memory configuration:
- 1024 x 8 or 512 x 16-bit organization
(93AA76)
- 2048 x 8 or 1024 x 16-bit organization
(93AA86)
Self-timed erase and write cycles
Automatic ERAL before WRAL
Power on/off data protection circuitry
Industry standard 3-wire serial I/O
Device status signal during erase/write cycles
Sequential read function
1,000,000 erase/write cycles ensured
Data retention > 200 years
8-pin PDIP/SOIC package
Temperature ranges available:
- Commercial (C): 0C to +70C
Description:
The Microchip Technology Inc. 93AA76/86 are 8K and
16K low voltage serial Electrically Erasable PROMs.
The device memory is configured as x8 or x16 bits
depending on the ORG pin setup. Advanced CMOS
technology makes these devices ideal for low power
nonvolatile memory applications. These devices also
have a Program Enable (PE) pin to allow the user to
write-protect the entire contents of the memory array.
The 93AA76/86 is available in standard 8-pin PDIP and
8-pin surface mount SOIC packages.
Package Types
Block Diagram
SOIC Package
PDIP Package
CS
CLK
DI
DO
V
SS
PE
V
CC
ORG
CS
CLK
DI
DO
V
CC
PE
ORG
V
SS
93AA76/86
93AA76/86
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
DO
CS
CLK
V
CC VSS
Memory
Array
Address
Decoder
Data
Register
Counter
Address
Output
Buffer
Mode
Decode
Logic
Generator
Clock
DI
PE
8K/16K 1.8V Microwire Serial EEPROM
Not recommended for new designs
Please use 93AA76C or 93AA86C.
21130F.book Page 1 Wednesday, December 5, 2012 2:47 PM
93AA76/86
DS21130F-page 2 1996-2012 Microchip Technology Inc.
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings
(†)
VCC.............................................................................................................................................................................7.0V
All inputs and outputs w.r.t. V
SS ........................................................................................................-0.6V to Vcc + 1.0V
Storage temperature ...............................................................................................................................-65°C to +150°C
Ambient temperature with power applied................................................................................................-40°C to +125°C
Soldering temperature of leads (10 seconds) .......................................................................................................+300°C
ESD protection on all pins..........................................................................................................................................4 kV
1.1 AC Test Conditions
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at these or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to Absolute Maximum Rating
conditions for extended periods may affect device reliability.
AC Waveform:
V
LO = 2.0V
V
HI = Vcc - 0.2V (Note 1)
V
HI = 4.0V for (Note 2)
Timing Measurement Reference Level:
Input 0.5 V
CC
Output 0.5 VCC
Note 1: For VCC 4.0V
2: For V
CC 4.0V
21130F.book Page 2 Wednesday, December 5, 2012 2:47 PM
1996-2012 Microchip Technology Inc. DS21130F-page 3
93AA76/86
TABLE 1-1: DC CHARACTERISTICS
DC CHARACTERISTICS
Applicable over recommended operating ranges shown below unless otherwise noted:
VCC = +1.8V to +6.0V
Commercial (C): T
A = 0°C to +70°C
Parameter Symbol Min. Max. Units Conditions
High-level input voltage V
IH1 2.0 VCC + 1 V VCC 2.7V
V
IH2 0.7 VCC VCC + 1 V VCC < 2.7V
Low-level input voltage V
IL1 -0.3 0.8 V VCC 2.7V
V
IL2 -0.3 0.2 VCC VVCC < 2.7V
Low-level output voltage V
OL1 —0.4VIOL = 2.1 mA; VCC = 4.5V
V
OL2 —0.2VIOL =100 A; VCC = VCC Min.
High-level output voltage V
OH1 2.4 V IOH = -400 A; VCC = 4.5V
V
OH2 VCC-0.2 V IOH = -100 A; VCC = VCC Min.
Input leakage current I
LI -10 10 AVIN = 0.1V to VCC
Output leakage current ILO -10 10 AVOUT = 0.1V to VCC
Pin capacitance
(all inputs/outputs)
CINT —7pF (Note 1)
T
A = +25°C, FCLK = 1 MHz
Operating current I
CC write 3 mA VCC = 5.5V
I
CC read 1
500
mA
A
FCLK = 3 MHz; VCC = 5.5V
F
CLK = 1 MHz; VCC = 3.0V
Standby current I
CCS 100
30
A
A
CLK = CS = 0V; VCC = 5.5V
CLK = CS = 0V; V
CC = 3.0V
DI = PE = V
SS
ORG = VSS or VCC
Note 1: This parameter is periodically sampled and not 100% tested.
21130F.book Page 3 Wednesday, December 5, 2012 2:47 PM

93AA76T/SN

Mfr. #:
Manufacturer:
Microchip Technology
Description:
EEPROM 516x8-1024x8 - 1.8V
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet