OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

M74HC4051RM13TR

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17
M74HC4051 Maximum ratings
7/17
Table 7. AC electrical characteristics (C
L
= 50 pF, Input t
r
= t
f
= 6ns)
Symbol Parameter
Test condition Value
Unit
V
CC
(V)
V
EE
(V)
T
A
= 25°C -40 to 85°C
-55 to
125°C
Min. Typ Max Min Max Min Max
Φ
I/O
Phase difference
between input
and output
2.0 GND 25 60 75 90
ns
4.5 GND 6 12 15 18
6.0 GND 5 10 13 15
4.5 -4.5 4
t
PZL
t
PZH
Output enable
time
2.0 GND
R
L
= 1 KΩ
64 225 280 340
ns
4.5 GND 18 45 56 68
6.0 GND 15 38 48 58
4.5 -4.5 18
t
PLZ
t
PHZ
Output disable
time
2.0 GND
R
L
= 1 KΩ
100 250 315 375
ns
4.5 GND 33 50 63 70
6.0 GND 28 43 54 64
4.5 -4.5 29
Table 8. Capacitive characteristics
Symbol Parameter
Test condition Value
Unit
V
CC
(V)
V
EE
(V)
T
A
= 25 °C
-40 to
85 °C
-55 to
125 °C
Min Typ Max Min Max Min Max
C
IN
Input capacitance 5.0 5 10 10 10 pF
C
I/O
Common terminal
capacitance
5.0 -5.0 36 70 70 70 pF
C
I/O
Switch terminal
capacitance
5.0 -5.0 7 15 15 15 pF
C
IOS
Feed through
capacitance
5.0 -5.0 0.95 2 2 2 pF
C
PD
Power dissipation
capacitance
(1)
5.0 GND 70 pF
1. C
PD
is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current
consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation.
I
CC(opr)
= C
PD
x V
CC
x f
IN
+ I
CC
.
Maximum ratings M74HC4051
8/17
Table 9. Analog switch characteristics (GND = 0 V; T
A
= 25°C)
Symbo
l
Parameter
Test condition Value Unit
V
CC
(V)
V
EE
(V)
V
IN
(V
p-p
)
Typ
Sine wave
distortion
2.25 -2.25 4
f
IN
= 1 KHz R
L
= 10 KΩ C
L
= 50 pF
0.025
%4.5 -4.5 8 0.020
6.0 -6.0 11 0.018
f
MAX
Frequency
response
(Switch on)
(1)
2.25 -2.25
Adjust f
IN
voltage to obtain 0 dBm at V
OS
.
Increase f
IN
Frequency until dB meter reads -3dB
R
L
= 50 Ω, C
L
= 10 pF, f
IN
= 1 KHz sine wave
120
MHz4.5 -4.5 190
6.0 -6.0 200
f
MAX
Frequency
response
(switch on)
(2)
2.25 -2.25
Adjust f
IN
voltage to obtain 0 dBm at V
OS
.
Increase f
IN
Frequency until dB meter reads -3dB
R
L
= 50Ω, C
L
= 10 pF, f
IN
= 1KHz sine wave
45
MHz4.5 -4.5 70
6.0 -6.0 85
Feed through
attenuation
(switch off)
2.25 -2.25
V
IN
is centered at (V
CC
- V
EE
)/2
Adjust input for 0 dBm
R
L
= 600 Ω, C
L
= 50 pF, f
IN
= 1 KHz sine wave
-50
dB4.5 -4.5 -50
6.0 -6.0 -50
Crosstalk
(control input to
signal output)
2.25 -2.25
Adjust R
L
at set up so that I
S
= 0A.
R
L
= 600 Ω, C
L
= 50 pF, f
IN
= 1 KHz square wave
60
mV4.5 -4.5 140
6.0 -6.0 200
Crosstalk
(between any
two switches)
2.25 -2.25
Adjust V
IN
to obtain 0d Bm at input
R
L
= 600 Ω, C
L
= 50 pF, f
IN
= 1 KHz sine wave
-50
dB4.5 -4.5 -50
6.0 -6.0 -50
1. Input common terminal, and measured at switch terminal.
2. Input switch terminal, and measured at common terminal.
These characteristics are determined by the design of the device.
M74HC4051 Maximum ratings
9/17
2.1 Switching characteristics test circuit
Figure 6. Output enable/disable time Figure 7. Crosstalk (control to output)
Figure 8. Bandwidth and feedthrough
attenuation
Figure 9. Crosstalk between any two
switches
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P17

M74HC4051RM13TR

Mfr. #:
Buy M74HC4051RM13TR
Manufacturer:
STMicroelectronics
Description:
Multiplexer Switch ICs Ana Multi/Demultiplx
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet