MBA02040D8760BC100

MBA/SMA 0204, MBB/SMA 0207, MBE/SMA 0414 - Precision
www.vishay.com
Vishay Beyschlag
Revision: 12-Feb-16
7
Document Number: 28767
For technical questions, contact: filmresistorsleaded@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Notes
(1)
± (0.03 % R + 0.01) for MBB/SMA 0207
(2)
± (0.15 % R + 0.05 ) for MBB/SMA 0207
4.23
Climatic
sequence:
± (0.05 % R + 0.01 )
no visible damage
± (0.1 % R + 0.01 )
no visible damage
± (0.25 % R +0.05 )
no visible damage
4.23.2 2 (Ba) Dry heat 125 °C; 16h
4.23.3 30 (Db)
Damp heat,
cyclic
55 °C; 24h;
90 %to100 %RH;
1 cycle
4.23.4 1 (Aa) Cold -55 °C; 2h
4.23.5 13 (M)
Low air
pressure
8.5kPa; 2h;
15 °Cto35 °C
4.23.6 30 (Db)
Damp heat,
cyclic
55 °C; 5days;
95% to100 %RH; 5 cycles
4.23.7 DC load Apply rated power for 1 min
4.24 78 (Cab)
Damp heat,
steady state
(40 ± 2) °C;
56days;
(93 ± 3) %RH
± (0.05 % R+ 0.01 ) ± (0.1 % R + 0.01 ) ± (0.25 % R+0.05 )
4.25.1
-
Endurance
at 70 °C:
Precision
operation
mode
U =or
U = U
max.
;
1.5 h on; 0.5 h off
70 °C; 1000 h ± (0.05 % R + 0.01 )
(1)
± (0.1 % R + 0.01 ) ± (0.25 % R + 0.05 )
(2)
70 °C; 8000 h ± (0.1 % R+0.01) ± (0.2 % R+0.01 ) ± (0.5 % R+0.05 )
-
Endurance
at 70 °C:
Standard
operation
mode
U =or
U = U
max.
;
1.5 h on; 0.5 h off
70 °C; 1000 h ± (0.25 % R + 0.05 )
(2)
--
70 °C; 8000 h ± (0.5 % R+0.05 )- -
4.25.3 -
Endurance at
upper
category
temperature
85 °C; 1000 h
125°C; 1000 h
-
± (0.05 % R + 0.01 )
-
± (0.1 % R + 0.01 )
-
± (0.25 % R + 0.05 )
4.29 45 (XA)
Component
solvent
resistance
Isopropyl alcohol
+23 °C; toothbrush method
Marking legible;
No visible damage
4.40 -
Electrostatic
discharge
(human body
model)
IEC 61340-3-1;
3 pos. + 3 neg.
MBA/SMA 0204: 2 kV
MBB/SMA 0207: 4 kV
MBE/SMA 0414: 6 kV
± (0.5 % R + 0.05 )
TEST PROCEDURES AND REQUIREMENTS
IEC
60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS PERMISSIBLE CHANGE
(R max.)
Stability for product types:
STABILITY
CLASS 0.05
STABILITY
CLASS 0.1
STABILITY
CLASS 0.25
MBA/SMA 0204 100 to 100 k 43 to 221 k 22 to 332 k
MBB/SMA 0207 100 to 270 k 43 to 510 k 22 to 1 M
MBE/SMA 0414 100 to 470 k 43 to 1 M 22 to 1.5 M
P
70
x R
P
70
x R
MBA/SMA 0204, MBB/SMA 0207, MBE/SMA 0414 - Precision
www.vishay.com
Vishay Beyschlag
Revision: 12-Feb-16
8
Document Number: 28767
For technical questions, contact: filmresistorsleaded@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DIMENSIONS
Note
(1)
For 7.5 M < 10.0 mm, use version MBB/SMA 0207... L0 (welding joint not lacquered)
MBB/SMA 0207 WITH RADIAL TAPING
LEAD SPACING (UB = 2.5 mm), SIZE 0207
LEAD SPACING (RB = 5.0 mm), SIZE 0207
DIMENSIONS - Leaded resistor types, mass and relevant physical dimensions
TYPE
D
max.
(mm)
L
max.
(mm)
d
nom.
(mm)
I
min.
(mm)
M
min.
(mm)
MASS
(mg)
MBA/SMA 0204 1.6 3.6 0.5 29.0 5.0 125
MBB/SMA 0207
(1)
2.5 6.3 0.6 28.0 10.0
(1)
220
MBE/SMA 0414 4.0 11.9 0.8 31.0 15.0 700
M
IL
d
D
L
H
C
H
1
F
P
3 max.
Insulated
W
Direction of unreeling
DIMENSIONS in millimeters
Pitch of components P 12.7 ± 1.0
Lead spacing F 2.5 + 0.6 / - 0.1
Width of carrier tape W 18.0 + 1.0 / - 0.5
Body to hole center H 18.0 ± 2.0
Height for cutting (max.) L 11
Height for bending C 2.5 + 0 / - 0.5
Height for insertion (max.) H1 32
H
1
L
H
C
P
F
H
0
W
Insulated
3 max.
Direction of unreeling
DIMENSIONS in millimeters
Pitch of components P 12.7 ± 1.0
Lead spacing F 5.0 + 0.6 / - 0.1
Width of carrier tape W 18.0 + 1.0 / - 0.5
Body to hole center H 18.0 ± 2.0
Lead crimp to hole center H
0
16.0 ± 0.5
Height for cutting (max.) L 11
Height for bending C 2.5 + 0 / - 0.5
Height for insertion (max.) H
1
32
MBA/SMA 0204, MBB/SMA 0207, MBE/SMA 0414 - Precision
www.vishay.com
Vishay Beyschlag
Revision: 12-Feb-16
9
Document Number: 28767
For technical questions, contact: filmresistorsleaded@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
HISTORICAL 12NC INFORMATION
The resistors had a 12-digit numeric code starting with
2312
The subsequent 4 digits indicated the resistor type,
specification and packaging; see the 12NC table
The remaining 4 digits indicated the resistance value:
- The first 3 digits indicated the resistance value
- The last digit indicated the resistance decade in
accordance with resistance decade table shown below
Resistance Decade
Historical 12NC Example
The 12NC code of a MBA 0204 resistor, value 47 k and
TCR 25 with ± 0.1 % tolerance, supplied on bandolier in a
box of 5000 units was: 2312 906 74703.
RESISTANCE DECADE LAST DIGIT
10 to99.9 9
100 to999 1
1 k to 9.99 k 2
10 k to99.9 k 3
100k to999 k 4
1M to9.99 M 5
HISTORICAL 12NC - Resistor type and packaging
DESCRIPTION
2312 ... ..... (BANDOLIER)
AMMOPACK REEL
TYPE TCR TOL. C1 1000 UNITS CT 5000 UNITS R1 1000 UNITS R2 2500 UNITS RP 5000 UNITS
MBA 0204
± 25 ppm/K
± 0.25 % 901 6.... 906 6.... 701 6.... - 806 6....
± 0.1 % 901 7.... 906 7.... 701 7.... - 806 7....
± 15 ppm/K
± 0.25 % 902 6.... 907 6.... 702 6.... - 807 6....
± 0.1 % 902 7.... 907 7.... 702 7.... - 807 7....
MBB 0207
± 25 ppm/K
± 0.25 % 911 6.... 916 6.... 711 6.... - 816 6....
± 0.1 % 911 7.... 916 7.... 711 7.... - 816 7....
± 15 ppm/K
± 0.25 % 912 6.... 917 6.... 712 6.... - 817 6....
± 0.1 % 912 7.... 917 7.... 712 7.... - 817 7....
MBE 0414
± 25 ppm/K
± 0.25 % 921 6.... - - 826 6.... -
± 0.1 % 921 7.... - - 826 7.... -
± 15 ppm/K
± 0.25 % 922 6.... - - 827 6.... -
± 0.1 % 922 7.... - - 827 7.... -

MBA02040D8760BC100

Mfr. #:
Manufacturer:
Description:
Thin Film Resistors - Through Hole MBA/SMA 0204-25 0.1% C1 876R
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union