4
FN6580.2
November 3, 2009
Absolute Maximum Ratings Thermal Information
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 7.0V
Input Voltages
NOx, NCx (Note 5) . . . . . . . . . . . . . . . . (V+ - 7V) to ((V+) + 0.5V)
INx (Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to ((V+) + 0.5V)
Output Voltages
COMx (Note 5) . . . . . . . . . . . . . . . . . . . (V+ - 7V) to ((V+) + 0.5V)
Continuous Current NOx, NCx, or COMx . . . . . . . . . . . . . . ±300mA
Peak Current NOx, NCx, or COMx
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . ±500mA
ESD Rating:
Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>6kV
Machine Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>400V
Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . >1.5kV
Thermal Resistance (Typical) θ
JA
(°C/W) θ
JC
(°C/W)
10 Ld 3x3 TDFN Package (Notes 6 and 8) 52 18
10 Ld µTQFN Package (Note 7) . . . . . 154 N/A
Maximum Junction Temperature (Plastic Package). . . . . . . +150°C
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to +150°C
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Power Supply Range. . . . . . . . . . . . . . . . . . . . . . . . +1.8V to +6.5V
AUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTES:
5. Signals on NC, NO, IN, or COM exceeding V+ or GND by the specified amount are clamped by internal diodes. Limit forward diode current to
maximum current ratings.
6. θ
JA
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
7. θ
JA
is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
8. For θ
JC
, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 9), Unless
Otherwise Specified.
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Notes 10, 11) TYP
MAX
(Notes 10, 11) UNITS
ANALOG SWITCH CHARACTERISTICS
ON-Resistance, r
ON
V+ = 4.5V, I
COM
= 100mA, V
NO
or V
NC
= (V+ -6.5)
to V+, (See Figure 4)
25 - 0.52 - Ω
Full - 0.68 - Ω
r
ON
Matching Between Channels,
ΔR
ON
V+ = 4.5V, I
COM
= 100mA, V
NO
or V
NC
= Voltage
at max r
ON,
(Note 13)
25 - 10 - mΩ
Full - 13.1 - mΩ
r
ON
Flatness, R
FLAT(ON)
V+ = 4.5V, I
COM
= 100mA, V
NO
or V
NC
= (V+ -6.5)
to V+, (Note 12)
25 - 0.11 - Ω
Full - 0.14 - Ω
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 5V, V
COM
= -1.5V, 5V, V
NO
or V
NC
= 5V,
-1.5V
25 - -8.13 - nA
Full - -0.4 - µA
COM ON Leakage Current,
I
COM(ON)
V+ = 5V, V
COM
= -1.5V, 5V, V
NO
or V
NC
= Float 25 - -4.42 - nA
Full - -0.33 - µA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 4.5V, V
NO
or V
NC
= 3.0V, R
L
= 50Ω,
C
L
= 35pF (see Figure 1)
25 - 35 - ns
Full - 30 - ns
Turn-OFF Time, t
OFF
V+ = 4.5V, V
NO
or V
NC
= 3.0V, R
L
= 50Ω,
C
L
= 35pF (see Figure 1)
25 - 10 - ns
Full - 15 - ns
Charge Injection, Q V
G
= 0V, R
G
= 0Ω, C
L
= 1.0nF (see Figure 2) 25 - 170 - pC
OFF-Isolation R
L
= 50Ω, C
L
= 5pF, f = 100kHz, V
COM
= 1V
RMS
(see Figure 3)
25 - 60 - dB
Crosstalk (Channel-to-Channel) R
L
= 50Ω, C
L
= 5pF, f = 1MHz, V
COM
= 1V
RMS
(see Figure 5)
25 - -75 - dB
Total Harmonic Distortion f = 20Hz to 20kHz, V
COM
= 0.5V
P-P
, R
L
= 32Ω 25 - 0.02 - %
-3dB Bandwidth V
COM
= 1V
RMS
, R
L
= 50Ω, C
L
= 5pF 25 - 60 - MHz
NO x or NCx OFF Capacitance,
C
OFF
f = 1MHz (see Figure 6) 25 - 36 - pF
COMx ON Capacitance, C
COM(ON)
f = 1MHz (See Figure 6) 25 - 88 - pF
ISL54060, ISL54061
