AO4892
Symbol Min Typ Max Units
BV
DSS
100 V
V
DS
=100V, V
GS
=0V 1
T
J
=55°C 5
I
GSS
±100 nA
V
GS(th)
Gate Threshold Voltage
1.7 2.35 2.8 V
I
D(ON)
25 A
56 68
T
J
=125°C 104 126
74 94 mΩ
g
FS
12.5 S
V
SD
0.78 1 V
I
S
2.5 A
C
iss
415 pF
C
oss
32 pF
C
rss
3 pF
R
g
0.7 1.4 2.1 Ω
Q
g
(10V) 6.5 12 nC
Q
g
(4.5V) 3 6 nC
Q
gs
1.5 nC
Q
gd
1.5 nC
t
D(on)
4 ns
Maximum Body-Diode Continuous Current
Input Capacitance
Output Capacitance
Turn-On DelayTime
DYNAMIC PARAMETERS
Reverse Transfer Capacitance
V
GS
=0V, V
DS
=50V, f=1MHz
SWITCHING PARAMETERS
Gate resistance
V
GS
=0V, V
DS
=0V, f=1MHz
Total Gate Charge
V
GS
=10V, V
DS
=50V, I
D
=4A
Gate Source Charge
Gate Drain Charge
Total Gate Charge
Zero Gate Voltage Drain Current
Gate-Body leakage current
mΩ
I
S
=1A,V
GS
=0V
V
DS
=5V, I
D
=4A
V
GS
=4.5V, I
D
=3A
Forward Transconductance
Diode Forward Voltage
Electrical Characteristics (T
J
=25°C unless otherwise noted)
STATIC PARAMETERS
Parameter Conditions
Drain-Source Breakdown Voltage
On state drain current
I
D
=250µA, V
GS
=0V
V
GS
=10V, V
DS
=5V
V
GS
=10V, I
D
=4A
R
DS(ON)
Static Drain-Source On-Resistance
I
DSS
µA
V
DS
=V
GS,
I
D
=250µA
V
DS
=0V, V
GS
=±20V
r
t
D(off)
15 ns
t
f
2 ns
t
rr
16 ns
Q
rr
44
nC
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
GS
DS
L
R
GEN
=3Ω
Body Diode Reverse Recovery Charge
I
F
=4A, dI/dt=500A/µs
Turn-Off DelayTime
I
F
=4A, dI/dt=500A/µs
Turn-Off Fall Time
Body Diode Reverse Recovery Time
A. The value of R
θJA
is measured with the device mounted on 1in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C. The
value in any given application depends on the user's specific board design.
B. The power dissipation P
D
is based on T
J(MAX)
=150°C, using ≤ 10s junction-to-ambient thermal resistance.
C. Repetitive rating, pulse width limited by junction temperature T
J(MAX)
=150°C. Ratings are based on low frequency and duty cycles to keep
initialT
J
=25°C.
D. The R
θJA
is the sum of the thermal impedance from junction to lead R
θJL
and lead to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-ambient thermal impedance which is measured with the device mounted on 1in
2
FR-4 board with
2oz. Copper, assuming a maximum junction temperature of T
J(MAX)
=150°C. The SOA curve provides a single pulse rating.
Rev 0: Nov. 2012 www.aosmd.com Page 2 of 6
