58577-1 Datasheet 58577-1, 58074-1, 58246-1 | P1-P3

Fast Facts

• Terminates 28-16 AWG [0.08-1.2 mm

]

wires

• No wire stripping needed for lower applied

cost

• Pistol grip (manual or air) or bench mount

(air or electric) power units

• Lightweight; easy to operate

• For prototypes or low- to medium-

volume production

• Small size; useful in confined work areas

• Interchangeable terminating heads:

• Pin and socket connectors

(AMPLIMITE HDE and MATE-N-LOK)

• Printed circuit board connectors

(AMPMODU, MT-6/MT-7, 2 mm CT,

and MTA)

• Category 5 connectors (CHAMP)

• Card edge connectors

• Most terminating heads can be rotated to

any angle

• Adjustment available for proper wire

insertion depth

• Most terminating heads automatically index

connectors to the next contact position, or

connectors can be advanced by hand to

any position

• Anti-backup pawl prevents connectors

from moving in the wrong direction

• Produced under a Quality Management

System certified to ISO 9001

Pistol Grip Hand Tool

System for IDCs

The Pistol Grip Hand Tool System

uses interchangeable terminating

heads to apply a broad range of

TE IDC products. The basic tool

requires a pistol grip handle

assembly and a terminating head;

power-assist and bench mount

versions are available to suit your

specific needs.

This system is well suited for low-

to medium-volume production.

Simply order the standard or

extended-wear terminating heads

based on your anticipated needs.

Since most terminating heads can

be rotated to any angle, the opera-

tor can also tackle more difficult

terminations in confined work

areas.

The terminating force is provided

by a manual-, pneumatic- or elec-

tric-powered assembly. The wire

inserter, inside each head, pushes

the end of an unstripped wire into

the insulation displacement con-

tact. Then, most tools automatical-

ly index the connector to the next

contact. The tools offer precise

termination depth control.

For maximum productivity, a

bench mount power unit (pneu-

matic or electric) is recommended.

Optional feed tracks can increase

application rates further. Actual

production rate depends on the

IDC product, discrete wire or rib-

bon cable, and operator dexterity.

Technical Documents

CCuussttoommeerr MMaannuuaall

409-5746—Electric Power Unit

IInnssttrruuccttiioonn SShheeeettss

408-6790—Pistol Grip Manual

Handle

Assembly

408-6789—Pistol Grip Pneumatic

Handle Assembly

408-9393—Bench Mount

Pneumatic Power Unit

Pistol Grip Hand Tool System

for Insulation Displacement Connectors (IDCs)

Pistol Grip Manual

Handle Assembly

Part Number 58074-1

A basic hand tool requires a

andle assembly and a termi-

ating head, ordered sepa-

rately, shown on page 4.

● Lightweight, easy to use

● Ratchet control will not

elease cam trigger until it

s fully bottomed

● R

atchet release

● “

U”-shaped key slides into

andle to hold interchange-

ble heads securely

● M

aterial (handle) — Molded

nylon

Specifications

Length — 3.75 [95.2]

Width — 1.12 [28.6]

Height — 4.00 [101.6]

Grip Span — 2.50 [63.5] over

trigger/handle

Weight — 3.5 oz [99 g]

Cycle Time — 0.7 - 0.8 s

Pistol Grip Pneumatic

Handle Assembly

Part Number 58075-1

● Lightweight

● Power assist for less

operator effort

● Push-button trigger

actuated

● Quiet — 78 dB max.

● “U”-shaped key slides into

handle to secure inter-

changeable heads

● Material (handle) — Molded

nylon

Specifications

Length — 4.88 [124]

Width — 1.13 [28.7]

Height — 6.00 [152]

Grip Span — 2.50 [63.5] over push-

button trigger/handle

Weight — 18 oz [510 g]

Air Pressure — 40 - 70 psi

[2.76 - 4.83 bar]

Air Supply Line (1) — 7 ft [2.13 m]

long, 3/16 [4.76] I.D. with 1/8 [3.18]

NPT fitting

Cycle Time — 0.7 - 0.8 s

Bench Mount

Pneumatic Power Unit

Part Number 58338-1

Assembly consists of a bench

mount with attached pneu-

matic power unit, a foot

switch, and two air lines

which connect the switch to

the power unit and the air

source to the switch.

Mounting hardware is not

included.

● Mounting bracket allows

interchangeable heads to

be pointed up or down to

suit operator

● Power assist for greater

productivity

● Actuated by foot switch

● Key retains heads, or heads

and feed tracks

Specifications

Outside Diameter — 1.62 [41.2]

Length — 5.00 [127]

Height — 7.00 [178]

Weight — 2 lb [0.91 kg]

Air Pressure — 40 - 70 psi

[2.76 - 4.83 bar]

Air Lines (2) — 7 ft [2.13 m] long,

3/16 [4.76] I.D. with 1/8 [3.18]

NPT fitting

Cycle Time — 0.7 - 0.8 s

Application Rates (Typ.) —

600 terminations per hr;

1 100 terminations per hr with optional

Loose-Piece Feed Track; and

1 250 terminations per hr with optional

Tape (Reel) Feed Track (when produc-

ing 6 in [15 cm] jumpers, one

4-pos. MTA-100 connector each end,

discrete wire)

Bench Mount Power Units

Notes: 1. Interchangeable terminating heads must be ordered separately, see page 4.

2. Loose-piece or tape (reel) feed track accessories are available, see page 3.

Pistol Grip Power Units

TE Terminating Head and Terminating Head, Terminating Head, Tube Feed Track,

IDC Product Loose-Piece Feed Track Tape Feed Track and Base and Seating Station

for Electric Power Unit Only

AMPMODU MTE Connectors ——

856675-1

(Instruction Sheet 408-9759)

MTA

MTA-100

933567-1 853546-1 and 853542-1 (Base)

—

Closed-End

(Instruction Sheet 408-9435) (Instruction Sheet 408-9636)

Receptacles

MTA-156

933568-1 853547-1 and 853542-1 (Base)

—

(Instruction Sheet 408-9466) (Instruction Sheet 408-9637)

Bench Mount

Electric Power Unit

art Number 931800-1

● P

ortable, compact

● L

ow noise

● S

emiautomatic operation

● F

oot pedal actuated

● F

eed track options

Specifications

Length — 14 [356]

Width — 7 [178]; 22 [559] with

feed track

Height — 10 [254]

Weight — 12 lb [5.44 kg]

Electrical Requirements — 120 VAC,

60 Hz, single phase, 2 A

Cycle Time — 0.5 s

Application Rates (Typ.) —

900 terminations per hr;

1 100 terminations per hr with optional

Loose-Piece Feed Track; and

1 250 terminations per hr with optional

Tape (Reel) Feed Track (when produc-

ing 6 in [15 cm] jumpers, one 4-pos.

MTA-100 connector each end, discrete

wire)

Notes:

. Interchangeable terminating heads must be

rdered separately, see page 4.

2. Loose-piece, tube or tape (reel) feed track

accessories are available, see below.

Accessories for Bench Mount Power Units

Loose-Piece, Tube or

Tape Feed Track Options

● No special setup required

● Connectors load easily into

feed track

● Simple, spring-loaded push-

er feeds connectors into

head

● Power Units shown for size

reference only

Terminating Head,

Tape Feed Track and Base

Terminating Head and

Loose-Piece Feed Track

Terminating Head, Tube Feed

Track and Seating Station

Part Numbers

Bench Mount Power Units (Continued)

Pistol Grip Hand Tool System

for Insulation Displacement Connectors (IDCs)

P1-P3 P4-P4

58577-1

Mfr. #:

Buy 58577-1

Manufacturer:

TE Connectivity / AMP Connectors

Description:

D-Sub Tools & Hardware HAND TOOL MOD MT

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

58577-1

58577-1

Products related to this Datasheet