TS2581CS RLG

TS2581
PWM Controller
1/7
Version: A11
SOP
-
8
General Description
The TS2581 integrates Pulse-Width-Modulation (PWM) control circuit into a single chip, mainly designs for power-
supply regulator. All the functions include an error amplifier, a soft-start, UVLO, OVP, SCP, TSD circuitry.
This device features an internal 100KHz oscillator, the UVLO makes sure that the outputs are off until the internal
circuit operates normally.
Features
Input voltage8V to 40V
Duty ratio0% to 100% PWM control
Oscillation frequency100K/300KHz
Thermal Shutdown function.
Short Circuit Protect (SCP).
External SW P-channel MOS.
External OVP setting function.
Current mode non-synchronous PWM converter
External current limit setting.
Under voltage Lockout.
Ordering Information
Part No. Package Packing
TS2581CS RLG SOP-8 2.5kpcs / 13” Reel
Note: “G” denotes for Halogen Free
Application
Simple High-efficiency Step down Regulator
Charger
Telecommunication
Absolute Maximum Rating
Parameter Symbol Limit Unit
VIN Pin Voltage V
IN
GND - 0.3 to GND + 45 V
VGATE,ISENSE Pin Voltage GND - 0.3 to V
IN
V
Feedback, OVP, EN/CT Pin Voltage GND - 0.3 to 6 V
Switch Pin Voltage V
SW
GND - 0.3 to V
IN
+ 0.3 V
Power Dissipation PD (T
J
– T
A
)/ θ
JA
W
Storage Temperature Range T
ST
-40 to +165 °C
Operating Temperature Range T
OP
-20 to +125 °C
Operating Supply Voltage V
OP
+8.5 to +40 V
Thermal Information
Parameter Symbol Maximum Unit
Thermal Resistance (Junction to Case) Ө
JC
15
o
C/W
Thermal Resistance (Junction to Ambient) Ө
JA
40
o
C/W
Note1: Ө
JA
is measured on the PCB with minimum copper area.
Note2: Ө
JA
is measured with the PCB copper area (need connect to GROUND pins) of approximately 0.5 in
2
Pin
:
1. EN/CT 8. FB
2. GND 7. OVP
3. V
GATE
6. V
SENSE
4. V
CC
5. GATE
TS2581
PWM Controller
2/7
Version: A11
Electrical Specifications
(Ta = 25
o
C unless otherwise noted, V
IN
=12V)
Characteristics Symbol Conditions Min.
Typ.
Max.
Units
Feedback Voltage V
FB
I
OUT
=10mA 0.98
1 1.02
V
Under Voltage Lockout U
VLO
Falling - 6 - V
UVLO Hysteresis - - 0.8 - V
OVP detect voltage V
OVP
Internal define 1.07
1.1 1.13
V
Line Regulation REG
LINE
V
IN
=10 ~ 40V, I
OUT
=10mA - 0.5 1 %
Load Regulation REG
LOAD
I
OUT
=0~3A, R
SENSE
= 33m - 30 50 mV
Quiescent Current I
CCQ
V
FB
= 1.5V, force driver off. - 3 6 mA
Oscillator frequency F
OSC
I
OUT
= 0.5A 70 100
130
KHz
Max. Duty Cycle (ON)
DC
Force driver on V
FB
= 0.6V - 100
- %
Min. Duty Cycle (OFF) Force driver off V
FB
= 1.5V - 0 - %
Sense Voltage VCC-V
SENSE
- 110
- mV
EN/CT pin logic input threshold
voltage
V
EN1
Shutdown mode - - 0.4
V
V
CT
Auto restart, VFB<0.4V 0.5 - 1.5
V
Thermal shutdown Temp T
SD
- 160
- °C
Thermal
Shutdown Hysteresis
T
SH
- 45 - °C
Block Diagram
OSC.
+
+
_
Thermal
Shutdown
CONTROL
+
DRIVER
COMP.
GATE
_
COMP.
Current
limit
+
_
AMP
CURRENT
SOURCE
BIAS
1.23V
REFERENCE
2.5 V
REGULATOR
1.00V
110 mV
+
_
AMP
+
_
AMP
0.4V
SCP
OVP
Line
Compensation
VGATE
VCC
GND
FB
VSENSE
1.10V
START-UP and
Auto restart control
EN/CT
OVP
Pin Function Description
Name Description
EN/CT Shutdown and auto restart control pin
GND GND pin
V
GATE
Driver gate clamping pin. The pin must connect a 1uF capacitor to VIN
V
CC
Operating voltage input
GATE Switch pin. Connect external inductor and diode here
V
SENSE
Voltage Sense input
OVP Over voltage detect pin
FB Feedback pin
TS2581
PWM Controller
3/7
Version: A11
Function Description
Feedback
Sense the regulated output voltage to complete the feedback loop, when VFB <0.4V, the SCP is happened.
VSENSE
The current limit sense pin, if V
IN
-V
SENSE
110mV, the over current is happened that it can turn-off driver cycle by
cycle.
OVP
The Over Voltage sense pin, If VOVP >1.10V, the OVP is happened that it can turn-off the driver. You can set
VOUT OVP voltage by outside resistances (R3 and R4), Please see below formula to set.
)
5R
2
R
+1(×10.1=VOUT
)OVP(
The Over Voltage Protect, If VOVP >1.10V, the OVP is happened that it can turn-off the driver.
Under Voltage Lockout (UVLO)
To avoid error-operation of the device at low input voltages an under voltage lockout is included that disables the
device, if the input voltage falls below 6.0V
Thermal Consderation
The SOP-8L package needs a heat sink under most conditions. The heat sink connect exposed pad of TS2581 to
obtain best effect. The size of the heat sink depends on the input voltage, output voltage, output current and
ambient temperature.
Typical Application Circuit
VCC 10~36V 5V/3A
U2
AX3304/A
1
2
3
4 5
6
7
8
EN/CT
GND
VGATE
VCC GATE
VSENSE
OVP
FB
D
S
U1
P-MOS
4
51
6
7
8
2
3
C3
1uF
D1
B340A
C5
Option
L1 66uH / 33uH
C7
0.1u
C6
Option
R4
Option
R5
3K
R2
12K
R1 0R
RSENSE1 33mR
R6
3K
R3
12K
C4
470uF
C2
0.1u
C1
470uF
ICL = ( VCC - Vsense ) / Rsense
TS2581

TS2581CS RLG

Mfr. #:
Manufacturer:
Taiwan Semiconductor
Description:
Switching Voltage Regulators PWM controller
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet