9SA10SBL6500 Datasheet 9SA10SQ6500, 9SA50RE4520, 9MA50RQ6295 | P1-P3

APEM www.apem.com

Note: The company reserves the right to change specifications without notice.

9000 series

Inductive sensing joysticks

Distinctive features and specifications

CABLE

TECHNICAL

14/0.12 – Fourteen strands of 0.12mm diameter tinned annealed copper wire PVC insulated, to a nominal OD of 1mm

• Red – +VCC • Black – 0V for X and Y axis

• Blue – X axis wiper • Yellow – Y axis wiper

• Green – Center tap Reference • White – Fault detect

• Orange – Center Detect or Combined • Gray – Mirror of Y axis wiper

Fault & Center Detect

• Brown – Mirror of X axis wiper

7/0.127 – Seven strands of 0.127mm diameter tinned copper wire ETFE insulated, to a nominal OD of 0.7mm

• Orange – Pushbutton

NOTES: 1. All 9000 series are supplied with 150mm of twisted cable harness, with tinned ends.

2. Connectors fitted upon request.

• Life Cycles: > 10 Million Operations • Supply Voltage: 4.75V Min to 15V Max

• Signal Swing: ±10% of VCC to ±50% of VCC • Output Signal Tolerance: ±10% of Output

• Output at Center: ±1% • Output Impedance: 1.8k ±1%

• Signal Ripple: <1% of Output • Supply Current: Typically 10mA

• ESD Immunity: >12KV – Correctly Installed • RFI Rejection: >20V/m – Bare Joystick

• RFI Rejection: >40V/m – Correctly Installed • Preferred Load: >10K

• Body Material: Glass Reinforced ABS • Shaft Material: Stainless Steel

• Shaft Diameter: 5mm • Other Materials: Brass, Acetal, Nylon

• Gimbal Pivot: Acetal & Hardened Steel • Boot: Neoprene

• Weight: 90 Grams (0.20lb) • Above Panel Seal: IP65

• Temperature Range: -20°C to +55°C (-4°F to +131°F) • Operating Lever Deflection: ±18%

 One or two axis

 Signal mixing options

 5 - 15V operation

 Dual redundant outputs.

 Infinite resolution

 Inductive sensing

 Consistent performance

 IP65 above panel

 Long service life

 Wide range of handles

 Optional “at center” and “internal fault”

detection

NOTES:

1. All values are nominal.

2. All specifications shown are based on a standard configuration and are provided for guidance only.

3. Please refer to APEM for assistance on how to achieve the best performance from your chosen configuration.

APEMwww.apem.com

Note: The company reserves the right to change specifications without notice.

9000 series

Inductive sensing joysticks

Overview

Gain

10 20% (±10%)

20 40% (±20%)

33 66% (±33%)

40 80% (±40%)

50 100% (±50%)

SERIES

9 9000

Sensing

M Mixed

Q Interacting

S Standard

Handle*

BL Round

D Cylindrical

E Conical

J Pushbutton Tactile

Q Skirted

U Fluted

AK One Pushbutton

AM Fluted with Pushbutton

AN Two Pushbuttons

AT Low Profile Conical

* for more handles see next pages

Bezel

0 Not Supplied

4 Circular R.M¹

6 Square D.I²

7 Circular D.I²

Limiter

A Single Axis

C Cross

D Diamond

R Round

S Square

X X Type

Boot

5 Standard

Decoding

A Single Decode

M Dual Decode/Dual Outputs

W Dual Decode/Separate Fault

& Center Detect

X Dual Decode/Fault Detect

Y Dual Decode/Combined Fault

& Center Detect

Z Dual Decode/Center Detect

Modifier

00 None

20 Guided Feel

1. Rear Mounting

2. Drop In Mounting

NOTES:

1. BEZEL OPTIONS

For drop in mounting, please specify bezel option 6 or 7. For sub-panel mounting, no bezel is necessary, unless the boot is required to seal

to the front face of the panel in which case bezel option 4 should be specified. Bezels 6 & 7 clamp the boot and top face of the joystick body

to the panel whereas bezel 4 clamps only the boot.

Some handles may be larger than some panel cut-outs. This may restrict the choice of mounting and bezel options. Please refer to APEM

for assistance.

2. SPRINGS

As standard 9000 series are offered sprung to center. The standard spring force requires 1.3N (nominally) to off-center the joystick. The

9000 series may be specified with a lighter spring (1N), or a stronger spring (1.6N)

Note: Forces quoted are subject to exact joystick configuration and are provided as a guide only.

3. DUAL DECODE INTERFACE

For optimum performance of the center detect and fault detect signals, Apem recommends the signals are “pulled high” via an input

resistor of typically 22K, on the controller circuitry.

4. CENTER TAP REFERENCE

All 9000 series output a center tap reference as standard. This reference is set within the joystick at 50% of VCC (±1%).

For optimum accuracy the outputs should be read relative to the center tap.

5. NON STANDARD

Further non standard options including custom handles or special limiters are available. Please refer to the factory for further details.

+Ve Supply

Y Axis Output

0V Supply

Center Tap

Reference

x 2

X Axis Output

Pushbutton

Dual Decode

NEAR EQUIVALENT CIRCUIT

APEM www.apem.com

Note: The company reserves the right to change specifications without notice.

9000 series

Inductive sensing joysticks

Overview

MATERIAL Nylon Aluminum Nylon ABS

FINISH Non Textured Anodized Sparked Matt Sparked Matt

STANDARD COLOR Black Black Black Black

OTHER COLORS NotNot AvailableAvailable Not Available Upon Request Upon Request

NOTES: Uses APEM IS Switches

MATERIAL Nylon Aluminum Aluminum ABS

FINISH Sparked Matt Anodized Anodized Sparked Matt

STANDARD COLOR Black Black Black Black

OTHER COLORS Upon Request Not Available Upon Request Upon Request

NOTES: Uses APEM IA Switches Uses APEM IA Switches Uses APEM IA Switches

31.00

(1.22)

13.60

(0.54)

17.50

(0.69)

15.00

(0.59)

25.00

(0.98)

18.00

(0.70)

46.00

(1.81)

42.30

(1.66)

MATERIAL Nylon Aluminum Delrin

FINISH Sparked Matt Anodized Gloss

STANDARD COLOR Black Black Black

OTHER COLORS Upon Request Not Available Not Available

NOTES: Uses APEM IS Switches

22.00

(0.86)

35.50

(1.39)

27.50

(1.08)

53.00

(2.08)

30.90

(1.22)

35.00

(1.38)

12.70

(0.50)

19.00

(0.74)

17.30

(0.68)

28.50

(1.12)

9.30

(0.37)

31.50

(1.23)

67.00

(2.63)

50.60

(1.98)

24.80

(0.97)

Ø31.30

(1.23)

29.60

(1.17)

35.00

(1.38)

NOTES:

1. Dimensions are in mm/(inch).

2. Unless otherwise specified, all joysticks are supplied with black switches in the handles.

R10.00

(0.39)

R7.50

(0.295)

29.52

(1.16)

P1-P3 P4-P6

9SA10SBL6500

Mfr. #:

Buy 9SA10SBL6500

Manufacturer:

APEM

Description:

Input Devices 1decdr 2gain Indctv SQR Lmtr RND Bzl

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

9SA10SBL6500

9SA10SBL6500

Products related to this Datasheet