OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

POE30U-560(G)-HT

P1-P3
Revision 11/17/2011
WWW.PHIHONG.COM
30W Power over Ethernet Adapter
High Power, High Temperature Single Port Injector
Features
Fully Compliant IEEE802.3af
UNH IOL Tested
Diagnostic LEDs
Full Protection OCP, OVP
Non-Vented Case
Gigabit Compatible
Wide Temperature Range: -20 to +55°C
Cisco AP1250 Full Power Support
Applications
IP Telephones
Security Cameras
Wireless Network Access Points
IP Print Servers
Blue Tooth Access Points
Safety Approvals
cUL/UL
CCC
CE
SAA
Korea K
S-Jet
C-Tick
IRAM
Mechanical Characteristics
Length: 166mm (6.48in)
Height: 44mm (1.73in)
Width: 80mm (3.15in)
Weight: 0.3Kg (0.5lb)
Output Specifications
Phihong is not responsible for any error, and reserves the right to make changes without notice. Please visit our website at
www.phihong.com for the most up-to-date specifications and contact information.
Model
DC Output
Voltage
Load Regulation
POE30U-560(G)-HT
56V
Min. Max. Line Load
0A
0.55A 54-57V DC under all conditions
POE30U-560(G)-HT Characteristics WWW.PHIHONG.COM
INPUT:
AC Input Voltage Range
85 to 264VAC
AC Input Voltage Rating
100 to 240VAC
AC Input Frequency
47-63Hz
AC Input Current
15A (RMS) maximum for 115VAC
20A (RMS) maximum for 230VAC
Leakage Current
0.25mA maximum for 264VAC 50Hz for input to PE
3.5mA maximum for 264VAC 50Hz for input to output
AC Inrush Current
15A (RMS) maximum for 115VAC
20A (RMS) maximum for 230VAC
OUTPUT:
Total Output Power
30W at 56V DC
DC Offset
No data degradation with DC imbalance 18mA per min.
Efficiency
75% (typical) at maximum load, and 120VAC 60Hz
Hold-up Time
16mS min. and 120VAC at maximum load
Transient O/P Voltage Protection
60V maximum zener clamp
ENVIRONMENTAL:
Temperature
Operation -20 to +55°C
Non-operation -40 to +85°C
Humidity 10 to 90%
EMC
FCC Part 15 Class B
EN55022 Class B
Isolation Test
Primary to Secondary: 4242VDC for 1 minute 10mA
Primary to F.G.: 2121VDC for 1 minute
Output to F.G.: 2121VDC
Immunity
ESD: EN61000-4-2. Level 3
RS: EN61000-4-3. Level 2
EFT: EN61000-4-4. Level 2
Surge: EN61000-4-5. Level 3
CS: EN61000-4-6. Level 2
Voltage Dips EN61000-4-11
Harmonic: EN61000-3-2
Insulation Resistance
Primary to Secondary: >10M OHM 500VDC
Primary to Field Ground: >10M OHM 500VDC
IEEE 802.3at Interoperability
UNH Interoperability report available upon request
FEATURE:
Cisco
No extern parts required for Legacy devices:
VoIP Phones:
7910, 7912, 7940, 7960
Access Points:
1040, 1140, 1250, 1260, 3500
Over Voltage/Current, Short Circuit Protection
The output can be shorted permanently without damage
Indicators
Green LED 1: Power detected “ON”
Green LED 2: Valid “PoE Plus” load detected and
connected
Green LED 3: Valid IEEE802.3af load detected and
connected
Input Connector
IEC320 inlet 3 pin
Output Connection
+pins 3, 6
-pins 1, 2
Dimension Diagram Unit: mm
Description of LED Functions for Gigabit Power Injector
Power-up Sequence:
Upon power-up, all 3 LEDs will light for 2 seconds, as part of the self-test for the internal microprocessor
software. After the 2 seconds, the "ON" LED will illuminate green. The DC output voltage is now available for
powering a compliant load (to the 802.3at PoE standards).
Detection Sequence:
Once a compliant load is attached to the output RJ45 connector, the green "CONNECT" LED will illuminate.
Should the load be non-compliant then the LEDs will blink a code signifying the cause for non-detection.
Detection Failure Codes:
1. Incorrect resistive signature – The green “CONNECT” and red “FAULT” LEDs will blink 3 times.
2. Incorrect capacitive signature – The green “ON” LED will blink 3 times.
3. Incorrect Voffset – The green “CONNECT” and green “ON” LEDs will blink 3 times.
4. Unstable current measurement – The green “ON” LED will blink 3 times
5. Low voltage sensed during detection (overload) – The red “FAULT” LED will blink 3 times
After the LEDs blink 3 times the Power Injector will continue to try to detect a valid load. Until the correct load is
applied, the LEDs will continue to blink. If there is an open circuit connected to the output RJ45 then the LEDs
will not blink but the Power Injector will continue to try to detect a valid load.
Fault Sequence:
Should a fault occur such as an overload or short circuit then the red "FAULT" LED will illuminate. The red
“FAULT” LED will illuminate for 2 seconds and then go off as the power supply tries to re-detect a valid load. If
there is a problem detecting the load, the LED will indicate the possible fault as per the codes in the
section above.
P1-P3

POE30U-560(G)-HT

Mfr. #:
Buy POE30U-560(G)-HT
Manufacturer:
Description:
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet