AOD452
Symbol Min Typ Max Units
BV
DSS
25 V
1
T
J
=55°C
5
I
GSS
100 nA
V
GS(th)
1.2 1.8 3 V
I
D(ON)
100 A
6.5 8.5
T
J
=125°C
9.7 12
11.5 14
m
g
FS
35 S
V
SD
0.72 1 V
I
S
55 A
C
iss
1230 1476 pF
C
oss
315 400 pF
C
rss
190 280 pF
R
g
1.2 2 Ω
Q
g
(10V)
26.4 32 nC
Q
g
(4.5V)
13.5 17 nC
Q
gs
3.9 5 nC
Q
gs(Vth)
1.3 2 nC
Q
gd
7.8 10 nC
t
D(on)
6.5 8 ns
t
r
10 20 ns
t
D(off)
22.7 30 ns
t
f
6.2 12 ns
t
rr
23.1
28 ns
Q
rr
15.3 18 nC
40
THIS PRODUCT HAS BEEN DESIGNED AND QUALIFIED FOR THE CONSUMER MARKET. APPLICATIONS OR USES AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS ARE NOT AUTHORIZED. AOS DOES NOT ASSUME ANY LIABILITY ARISING
OUT OF SUCH APPLICATIONS OR USES OF ITS PRODUCTS. AOS RESERVES THE RIGHT TO IMPROVE PRODUCT DESIGN,
FUNCTIONS AND RELIABILITY WITHOUT NOTICE.
Body Diode Reverse Recovery Charge
I
F
=20A, dI/dt=100A/µs
Maximum Body-Diode Continuous Current
Input Capacitance
Output Capacitance
Turn-On DelayTime
DYNAMIC PARAMETERS
Turn-On Rise Time
Turn-Off DelayTime
V
GS
=10V, V
DS
=12.5V, R
L
=0.6Ω,
R
GEN
=3Ω
Gate resistance V
GS
=0V, V
DS
=0V, f=1MHz
Turn-Off Fall Time
Total Gate Charge
V
GS
=10V, V
DS
=12.5V, I
D
=20A
Gate Source Charge
Gate Drain Charge
Total Gate Charge
Gate Source Charge at Vth
mΩ
I
S
=1A, V
GS
=0V
V
DS
=5V, I
D
=10A
V
GS
=4.5V, I
D
=20A
Forward Transconductance
Diode Forward Voltage
R
DS(ON)
Static Drain-Source On-Resistance
I
DSS
µA
Gate Threshold Voltage V
DS
=V
GS
,
I
D
=250µA
V
DS
=20V, V
GS
=0V
V
DS
=0V, V
GS
=±20V
Zero Gate Voltage Drain Current
Gate-Body leakage current
Electrical Characteristics (T
J
=25°C unless otherwise noted)
STATIC PARAMETERS
Parameter Conditions
Body Diode Reverse Recovery Time
Drain-Source Breakdown Voltage
On state drain current
I
D
=250uA, V
GS
=0V
V
GS
=10V, V
DS
=5V
V
GS
=10V, I
D
=30A
Reverse Transfer Capacitance
I
F
=20A, dI/dt=100A/µs
V
GS
=0V, V
DS
=12.5V, f=1MHz
SWITCHING PARAMETERS
A: The value of R
θJA
is measured with the device mounted on 1in
2
FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C. The
Power dissipation P
DSM
is based on R
θJA
and the maximum allowed junction temperature of 150°C. The value in any given application depends on
the user's specific board design, and the maximum temperature of 175°C may be used if the PCB allows it.
B. The power dissipation P
D
is based on T
J(MAX)
=175°C, using junction-to-case thermal resistance, and is more useful in setting the upper
dissipation limit for cases where additional heatsinking is used.
C: Repetitive rating, pulse width limited by junction temperature T
J(MAX)
=175°C.
D. The R
θJA
is the sum of the thermal impedence from junction to case R
θJC
and case to ambient.
E. The static characteristics in Figures 1 to 6 are obtained using <300 µs pulses, duty cycle 0.5% max.
F. These curves are based on the junction-to-case thermal impedence which is measured with the device mounted to a large heatsink, assuming a
maximum junction temperature of T
J(MAX)
=175°C.
G. The maximum current rating is limited by bond-wires.
H. These tests are performed with the device mounted on 1 in 2 FR-4 board with 2oz. Copper, in a still air environment with T
A
=25°C. The SOA
curve provides a single pulse rating.
Rev 7 : Feb 2010
Alpha & Omega Semiconductor, Ltd. www.aosmd.com
