7
PC3SD11NTZ Series
0
10
20
30
40
50
60
70
Forward current I
F
(mA)
Ambient temperature T
a
(˚C)
30 0 50 100
Fig.1 Forward Current vs. Ambient
Temperature
Fig.2 RMS ON-state Current vs.
Ambient Temperature
Sheet No.: D2-A07501EN
0
25
50
75
100
125
150
175
30 0 50 100
RMS ON-state current I
r
(rms) (mA)
Ambient temperature T
a
(˚C)
1
5
10
0.9 1.11 1.2 1.3 1.4 1.5
50
100
Forward current I
F
(mA)
Forward voltage V
F
(V)
T
a
=75˚C
50˚C
25˚C
0˚C
25˚C
Fig.3-b
Forward Current vs. Forward Voltage
(Rank B, Rank C)
Fig.4-b
Minimum Trigger Current vs. Ambient
Temperature (Rank B, Rank C)
Fig.3-a
Forward Current vs. Forward Voltage
(Rank A)
Fig.4-a
Minimum Trigger Current vs. Ambient
Temperature (Rank A)
0
2
4
6
8
10
40 020 20 40 60 80 100
Minimum trigger current I
FT
(mA)
Ambient temperature T
a
(˚C)
V
D
=6V
R
L
=100
0 0.5 1 1.5 2 2.5 3
Forward current I
F
(mA)
Forward voltage V
F
(V)
1
5
10
50
100
T
a
=100°C
75°C
50°C
25°C
0°C
30°C
0
2
4
6
8
10
40 020 20 40 60 80 100
Minimum trigger current I
FT
(mA)
Ambient temperature T
a
(˚C)
V
D
=6V
R
L
=100
8
PC3SD11NTZ Series
Fig.9-b Turn-on Time vs. Forward Current
(Rank B, Rank C)
Fig.9-a Turn-on Time vs. Forward Current
(Rank A)
Sheet No.: D2-A07501EN
10
10
10
8
10
6
40 020 20 40 60 80 100
Repetitive peak OFF-state current I
DRM
(A)
Ambient temperature T
a
(˚C)
10
7
10
9
V
D
=600V
Remarks : Please be aware that all data in the graph are just for reference.
Fig.8 Repetitive Peak OFF-state Current vs.
Ambient Temperature
10
100
1 000
110100
Turn-on time t
ON
(µs)
Forward current I
F
(mA)
V
D
=6V
R
L
=100
T
a
=25˚C
Fig.7 Holding Current vs.
Ambient Temperature
0.1
1
10
40 020 20 40 60 80 100
Holding current I
H
(mA)
Ambient temperature T
a
(˚C)
V
D
=6V
Fig.6 ON-state Voltage vs.
Ambient Temperature
1
1.2
1.4
1.6
1.8
2
2.2
2.4
40 020 20 40 60 80 100
ON-state voltage V
T
(V)
Ambient temperature T
a
(˚C)
I
T
=100mA
Fig.5 Relative Repetitive Peak OFF-state
Voltage vs. Ambient Temperature
0.7
0.8
0.9
1
1.1
1.2
1.3
40 020 20 40 60 80 100
Relative repetitive peak OFF-state voltage
V
DRM
(T
j
=T
a
) / V
DRM
(T
j
=25˚C)
Ambient temperature T
a
(˚C)
10
100
1 000
110100
Turn-on time t
ON
(µs)
Forward current I
F
(mA)
V
D
=6V
R
L
=100
T
a
=25˚C
Recommended Foot Print (reference)
9
SMT Gullwing Lead-form Wide SMT Gullwing Lead-form
2.542.54
1.7
2.2
10.2
2.542.54
1.7
2.2
8.2
(Unit : mm)
PC3SD11NTZ Series
Design Considerations
In order for the Phototriac to turn off, the triggering current (I
F
) must be 0.1mA or less.
Please refrain from using these devices in a direct drive configuration.
These Phototriac Coupler are intended to be used as triggering device for main Triacs.
Please ensure that the output rating of these devices will be sufficient for triggering the main output Triac of
your choice. Failure to do may result in malfunctions.
In phase control applications or where the Phototriac Coupler is being by a pulse signal, please ensure that
the pulse width is a minimum of 1ms.
For designs that will experience excessive noise or sudden changes in load voltage, please include an
appropriate snubber circuit as shown in the below circuit.
Please keep in mind that Sharp Phototriac Couplers incorporate superor dV/dt ratings which can often
eliminate the need for a snubber circuit.
Degradation
In general, the emission of the IRED used in Phototriac Couplers will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these Phototriac Couplers should
provide at least twice the minimum required triggering current from initial operation.
Design guide
Sheet No.: D2-A07501EN

PC3SD11NTZBH

Mfr. #:
Manufacturer:
Sharp Microelectronics
Description:
Triac & SCR Output Optocouplers Phototriac Coupler
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union