OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HMC788ALP2ETR

P1-P3P4-P6
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
AMPLIFIERS - DRIVER & GAIN BLOCK - SMT
4
HMC788ALP2E
v00.0913
pHEMT GAIN BLOCK
MMIC AMPLIFIER, DC - 10 GHz
Outline Drawing
Absolute Maximum Ratings
Typical Supply Current
Collector Bias Voltage (Vcc) +7V
RF Input Power (RFIN)(Vs = +5V) +15 dBm
Junction Temperature 150 °C
Continuous Pdiss (T = 85 °C)
(derate 8.5 mW/°C above 85 °C)
0.55 W
Thermal Resistance
(junction to ground paddle)
118 °C/W
Storage Temperature -65 to +150 °C
Operating Temperature -40 to +85 °C
ESD Sensitivity (HBM) Class 1A
Vcc (V) Icq (mA)
4.5 65
5.0 76
5.5 87
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PAT TERN.
Part Number Package Body Material Lead Finish MSL Rating Package Marking
[1]
HMC788ALP2E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn
MSL1
[2]
788A
XXXX
[1] 4-Digit lot number XXXX
[2] Max peak reow temperature of 260 °C
Package Information
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
AMPLIFIERS - DRIVER & GAIN BLOCK - SMT
5
HMC788ALP2E
v00.0913
pHEMT GAIN BLOCK
MMIC AMPLIFIER, DC - 10 GHz
Application Circuit
Pin Descriptions
Pin Number Function Description Interface Schematic
1, 4, 6 N/C
The pins are not connected internally; however, all data
shown herein was measured with these pins connected to
RF/DC ground externally.
2 RFIN
This pin is DC coupled.
An off chip DC blocking capacitor is required.
5 RFOUT RF output and DC Bias for the output stage.
3 GND
This pin and exposed ground paddle must
be connected to RF/DC ground.
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
AMPLIFIERS - DRIVER & GAIN BLOCK - SMT
6
HMC788ALP2E
v00.0913
pHEMT GAIN BLOCK
MMIC AMPLIFIER, DC - 10 GHz
Evaluation PCB
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ohm impedance while the package ground
leads and exposed paddle should be connected
directly to the ground plane similar to that shown.
A sufficient number of via holes should be used to
connect the top and bottom ground planes. The
evaluation board should be mounted to an appro-
priate heat sink. The evaluation circuit board shown
is available from Hittite upon request.
List of Materials for Evaluation PCB EV1HMC788ALP2
[1]
Item Description
J1 - J2 PC Mount SMA Connector
J5, J6 DC Pin
C1, C2 0.01 µF Capacitor, 0502 Pkg.
C3 100 pF Capacitor, 0402 Pkg.
C4 2.2 µF Case A Pkg.
R1 0 Ohm Resistor, 0402 Pkg.
L1 Inductor, Conical 6.35 µH
U1 HMC788ALP2E
PCB
[2]
129549 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
P1-P3P4-P6

HMC788ALP2ETR

Mfr. #:
Buy HMC788ALP2ETR
Manufacturer:
Analog Devices / Hittite
Description:
RF Amplifier upscreen part for Space
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet