OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

DLP-245PB-G

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16
V2.3 Page 13 of 15 February 2007
15 GROUND
16
SWVCC (Out) Power from EXTVCC (Pin 19) controlled via Pin 10 (POWERN#) of the FT245RL
and Q1 MOSFET power switch. R5 and C3 control the power-up rate to help limit inrush current.
17 GROUND
18
No connect
19
EXTVCC (In) Use for applying main power (4.4 to 5.25 volts) to the module. Connect to
PORTVCC if the module is to be powered by the USB port (typical configuration).
20
PORTVCC (Out) Power from USB port. Connect to EXTVCC if module is to be powered by the
USB port (typical configuration). 500mA is the maximum current available to the DLP-245PB-G
and target electronics if the USB device is configured for high power.
21
DB7 (I/O) Line 7 of the data bus between the 16F877A and the FT245RL USB-FIFO.
22
DB6 (I/O) Line 6 of the data bus between the 16F877A and the FT245RL USB-FIFO.
23
DB5 (I/O) Line 5 of the data bus between the 16F877A and the FT245RL USB-FIFO.
24
DB4 (I/O) Line 4 of the data bus between the 16F877A and the FT245RL USB-FIFO.
25
DB3 (I/O) Line 3 of the data bus between the 16F877A and the FT245RL USB-FIFO.
26
DB2 (I/O) Line 2 of the data bus between the 16F877A and the FT245RL USB-FIFO.
27
DB1 (I/O) Line 1 of the data bus between the 16F877A and the FT245RL USB-FIFO.
28
DB0 (I/O) Line 0 of the data bus between the 16F877A and the FT245RL USB-FIFO.
29
B5 (I/O) Port Pin B5 connected to the 16F877A microcontroller.
30
B4 (I/O) Port Pin B4 connected to the 16F877A microcontroller.
31
B0 (I/O) Port Pin B0 connected to the 16F877A microcontroller.
32
C0 (I/O) Port Pin C0 connected to the 16F877A microcontroller.
33
C1 (I/O) Port Pin C1 connected to the 16F877A microcontroller.
34
C2 (I/O) Port Pin C2 connected to the 16F877A microcontroller.
35
C3 (I/O) Port Pin C3 connected to the 16F877A microcontroller.
36
C4 (I/O) Port Pin C4 connected to the 16F877A microcontroller.
37
C5 (I/O) Port Pin C5 connected to the 16F877A microcontroller.
38
C6 (I/O) Port Pin C6 connected to the 16F877A microcontroller.
39
C7 (I/O) Port Pin C7 connected to the 16F877A microcontroller.
40 GROUND
V2.3 Page 14 of 15 February 2007
MECHANICAL DRAWINGS (PRELIMINARY)
INCHES (MILLIMETERS) UNLESS OTHERWISE NOTED
0.19 typ
(4.9 typ)
0.23 typ
(5.8 typ)
Side View
0.65 typ
(16.6 typ)
0.70 typ
(17.8 typ)
2.30 typ
(58.4 typ)
0.33 typ
(8.5 typ)
2.59 typ
(65.8 typ)
0.14 typ
(3.6 typ)
0.25 typ
(6.4 typ)
0.60 typ
(15.3 typ)
DISCLAIMER
Neither the whole nor any part of the information contained within or the product described in this
datasheet may be adapted or reproduced in any material or electronic form without the prior
written consent of the copyright holder.
This product and its documentation are supplied on an as-is basis, and no warranty as to their
suitability for any particular purpose is either made or implied. DLP Design will not accept any
claim for damages whatsoever arising as a result of use or failure of this product. Your statutory
rights are not affected.
V2.3 Page 15 of 15 February 2007
This product or any variant of it is not intended for use in any medical appliance, device, or
system in which the failure of the product might reasonably be expected to result in personal
injury.
This document provides preliminary information that may be subject to change without notice.
CONTACT INFORMATION
DLP Design
1605 Roma Lane
Allen, TX 75013
Phone: 469-964-8027
Fax: 415-901-4859
Email: support@dlpdesign.com
Internet: http://www.dlpdesign.com
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16

DLP-245PB-G

Mfr. #:
Buy DLP-245PB-G
Manufacturer:
DLP Design
Description:
MODULE USB-MCU FT245RL W/16F877A
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet