FPC connectors Y4BH (0.4mm pitch)
–2–
ACCTB67E 201701-T
PRODUCT TYPES
Notes: 1. Order unit; For volume production: 1-inner carton (1-reel) units.
For samples, please contact our sales office.
2. Please contact our sales office for connectors having a number of pins other than those listed above.
SPECIFICATIONS
1. Characteristics
The followings show specifications, when using an applicable FPC (thickness 0.30 mm)
2. Material and surface treatment
Height Differential impedance Number of pins Part number
Packing
Inner carton (1-reel) Outer carton
1.0 mm
85Ω and 90Ω types
40 AYF424035
5,000 pieces 10,000 pieces
50 AYF425035
100Ω type
40 AYF414035
50 AYF415035
Item Specifications Conditions
Electrical
characteristics
Rated current 0.3A/pin contact
Rated voltage 50V AC/DC
Insulation resistance Min. 1,000MΩ (initial) Using 250V DC megger (applied for 1 min.)
Dielectric strength 250V AC for 1 min.
No short-circuiting or damage at a detection current of 1 mA
when the specified voltage is applied for one minute.
Contact resistance Max. 100mΩ
Based on the contact resistance measurement method
specified by JIS C 5402.
Differential impedance
85Ω and 90Ω types
85Ω±10Ω (Connector part)
90Ω±10Ω (Connector part)
Differential signal
Rise times (Tr): 40 ps (20% to 80%)
(FPC and PC board: Differential impedance 85Ω or 90Ω
controlled.)
100Ω type 100Ω±15Ω (Connector part)
Differential signal
Rise times (Tr): 40 ps (20% to 80%)
(FPC and PC board: Differential impedance 100Ω
controlled.)
Mechanical
characteristics
FPC holding force Min. 0.10N/pin contact × pin contacts (initial)
Measurement of the maximum force applied until the
inserted compatible FPC is pulled out in the insertion axis
direction while the connector lever is closed
Environmental
characteristics
Ambient temperature –55°C to +85°C
No icing or condensation.
Storage temperature
–55°C to +85°C (Product only)
–40°C to +50°C (Emboss packaging)
Thermal shock resistance
(with FPC mated)
5 cycles,
insulation resistance min. 100MΩ,
contact resistance max. 100mΩ
Conformed to MIL-STD-202F, method 107G
Humidity resistance
(with FPC mated)
120 hours,
insulation resistance min. 100MΩ,
contact resistance max. 100mΩ
Conformed to IEC60068-2-78
Bath temperature 40°C±2°C,
humidity 90% to 95% R.H.
Saltwater spray resistance
(with FPC mated)
24 hours,
insulation resistance min. 100MΩ,
contact resistance max. 100mΩ
Conformed to IEC60068-2-11
Bath temperature 35°C±2°C,
saltwater concentration 5%±1%
H2S resistance
(with FPC mated)
48 hours,
contact resistance max. 100mΩ
Bath temperature 40°C±2°C,
gas concentration 3 ppm ±1 ppm,
humidity 75% to 80% R.H.
Soldering heat resistance
Peak temperature: 260°C or less Reflow soldering
300°C within 5 sec. 350°C within 3 sec. Soldering iron
Lifetime
characteristics
Insertion and removal life 20 times Repeated insertion and removal: min. 10 sec./time
Unit weight 50 pin contacts: 0.10 g
Part name Material Surface treatment
Molded portion
Housing: LCP resin (UL94V-0)
Lever: LCP resin (UL94V-0)
—
Contact Copper alloy
Contact portion; Base: Ni plating, Surface: Au plating
Terminal portion; Base: Ni plating, Surface: Au plating
Order Temperature (°C) Time (minutes)
1
2
3
4
–55
85
–55
0
−3
30
Max. 5
30
Max. 5
+3
0
0
−3