EVAL-10MSOPEBZ Datasheet EVAL-10MSOPEBZ | P1-P3

EVAL-10MSOPEBZ User Guide

UG-1037

One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Te l: 781.329.4700 • Fax: 781.461.3113 • www.analog.com

Evaluation Board for 10-Lead MSOP Devices in the Switches and Multiplexers Portfolio

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT

WARNING AND LEGAL TERMS AND CONDITIONS.

Rev. 0 | Page 1 of 6

FEATURES

10-lead MSOP evaluation board

Clamp allows the main device to be easily changed

Gold pin connectors allow the addition of passive

components

SMB connectors for the input/output of signals

Additional space on-board to allow for prototyping

EVALUATION KIT CONTENTS

EVAL-10MSOPEBZ evaluation board

ONLINE RESOURCES

Documents Needed

Data sheet of the device being evaluated

EVAL-10MSOPEBZ user guide

EQUIPMENT NEEDED

Device being evaluated

DC voltage source

Analog signal source

Method to measure voltage, such as a digital multimeter (DMM)

GENERAL DESCRIPTION

The EVAL-10MSOPEBZ evaluation board evaluates 10-lead

MSOP devices in the Switches and Multiplexers Portfolio that

are purchased separately. A clamp is supplied with the EVAL-

10MSOPEBZ to secure a 10-lead MSOP device to the evaluation

board without the need for soldering, making the EVAL-

10MSOPEBZ evaluation board reusable for multiple devices.

Figure 1 shows the EVAL-10MSOPEBZ evaluation board. A

10-lead MSOP device can be clamped or soldered to the center

of the EVAL-10MSOPEBZ evaluation board. Each pin of the

device has a corresponding link from K1 to K10 that can be set

to either VDD or GND. A wire screw terminal supplies VDD

and GND. SMB connectors on the board allow additional external

signals to be supplied to the device. In addition, there is space

available at the top of the EVAL-10MSOPEBZ evaluation board

for prototyping.

Full specifications of the device under test (DUT) are available

in the corresponding product data sheet, which should be

consulted in conjunction with this user guide when using the

evaluation board.

EVAL-10MSOPEBZ EVALUATION BOARD PHOTOGRAPH

Figure 1.

14928-001

UG-1037 EVAL-10MSOPEBZ User Guide

Rev. 0 | Page 2 of 6

TABLE OF CONTENTS

Features .............................................................................................. 1

Evaluation Kit Contents ................................................................... 1

Online Resources .............................................................................. 1

Equipment Needed ........................................................................... 1

General Description ......................................................................... 1

EVA L -10MSOPEBZ Evaluation Board Photograph .................... 1

Revision History ............................................................................... 2

Evaluation Board Hardware ............................................................ 3

Power Supply ..................................................................................3

Link Headers ..................................................................................3

SMB Connectors............................................................................3

Input Signal Traces ........................................................................3

Evaluation Board Schematic and Artwork .....................................4

Ordering Information .......................................................................6

Bill of Materials ..............................................................................6

REVISION HISTORY

8/2016—Revision 0: Initial Version

EVAL-10MSOPEBZ User Guide UG-1037

Rev. 0 | Page 3 of 6

EVALUATION BOARD HARDWARE

POWER SUPPLY

Connector J5 supplies the VDD and GND supplies to the

EVAL-10MSOPEBZ evaluation board. These supplies can be

selected for each pin of the device by setting the link headers

to either VDD or GND. When a VSS supply is needed, apply

the voltage directly to the VSS pin of the device by removing the

corresponding link completely and applying the voltage directly

to the middle pin of the link header.

LINK HEADERS

The link headers supply the DUT with either VDD or GND.

The headers are designated as K1 to K10 with the number

corresponding to the pin number of the device. Table 1 summarizes

these link headers, and how these headers function on the E VA L -

10MSOPEBZ evaluation board.

Table 1. Link Header Descriptions

Label Position Description

K1to K10 High VDD

Low GND

SMB CONNECTORS

There are four SMB connectors on evaluation board, J1 to J4.

When an SMB cable is connected to one of these connectors,

the input signal becomes available on the corresponding P1 to

P4 port. Apply this signal to the relevant pin of the device by

forming a connection from P1 to P4 to a gold pin connector

found on the relevant trace.

INPUT SIGNAL TRACES

Each trace includes three sets of gold pin connectors, two sets that

can place a load on the signal path to ground and another set that

is in series with the signal path. The three sets of gold pin

connectors can create a simple resistor capacitor (RC) filter.

P1-P3 P4-P6

EVAL-10MSOPEBZ

Mfr. #:

Buy EVAL-10MSOPEBZ

Manufacturer:

Analog Devices Inc.

Description:

Switch IC Development Tools Evaluation board i.c.

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

EVAL-10MSOPEBZ