MC10E163, MC100E163
http://onsemi.com
3
Table 3. MAXIMUM RATINGS
Symbol Parameter Condition 1 Condition 2 Rating Unit
V
CC
PECL Mode Power Supply V
EE
= 0 V 8 V
V
I
PECL Mode Input Voltage
NECL Mode Input Voltage
V
EE
= 0 V
V
CC
= 0 V
V
I
v V
CC
V
I
w V
EE
6
−6
V
V
I
out
Output Current Continuous
Surge
50
100
mA
mA
T
A
Operating Temperature Range 0 to +85 °C
T
stg
Storage Temperature Range −65 to +150 °C
q
JA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
PLCC−28
PLCC−28
63.5
43.5
°C/W
°C/W
q
JC
Thermal Resistance (Junction−to−Case) Standard Board PLCC−28 22 to 26 °C/W
T
sol
Wave Solder Pb
Pb−Free
265
265
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. 10E SERIES PECL DC CHARACTERISTICS V
CCx
= 5.0 V; V
EE
= 0.0 V (Note 1)
0°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 73 88 73 88 73 88 mA
V
OH
Output HIGH Voltage (Note 2) 3980 4070 4160 4020 4105 4190 4090 4185 4280 mV
V
OL
Output LOW Voltage (Note 2) 3050 3210 3370 3050 3210 3370 3050 3227 3405 mV
V
IH
Input HIGH Voltage 3830 3995 4160 3870 4030 4190 3940 4110 4280 mV
V
IL
Input LOW Voltage 3050 3285 3520 3050 3285 3520 3050 3302 3555 mV
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current 0.5 0.3 0.5 0.25 0.3 0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary −0.46 V / +0.06 V.
2. Outputs are terminated through a 50 W resistor to V
CC
− 2.0 V.
Table 5. 10E SERIES NECL DC CHARACTERISTICS V
CCx
= 0.0 V; V
EE
= −5.0 V (Note 3)
0°C 25°C 85°C
Symbol Characteristic Min Typ Max Min Typ Max Min Typ Max Unit
I
EE
Power Supply Current 73 88 73 88 73 88 mA
V
OH
Output HIGH Voltage (Note 4) −1020 −930 −840 −980 −895 −810 −910 −815 −720 mV
V
OL
Output LOW Voltage (Note 4) −1950 −1790 −1630 −1950 −1790 −1630 −1950 −1773 −1595 mV
V
IH
Input HIGH Voltage −1170 −1005 −840 −1130 −970 −810 −1060 −890 −720 mV
V
IL
Input LOW Voltage −1950 −1715 −1480 −1950 −1715 −1480 −1950 −1698 −1445 mV
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current 0.5 0.3 0.5 0.065 0.3 0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
3. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary −0.46 V / +0.06 V.
4. Outputs are terminated through a 50 W resistor to V
CC
− 2.0 V.
