VSC7435XMT

Microsemi makes no warranty, representation, or guarantee regarding the information contained herein or the suitability of its products and services for any particular purpose, nor does Microsemi assume any liability

whatsoever arising out of the application or use of any product or circuit. The products sold hereunder and any other products sold by Microsemi have been subject to limited testing and should not be used in conjunction

with mission-critical equipment or applications. Any performance specifi cations are believed to be reliable but are not verifi ed, and Buyer must conduct and complete all performance and other testing of the products, alone

and together with, or installed in, any end-products. Buyer shall not rely on any data and performance specifi cations or parameters provided by Microsemi. It is the Buyer’s responsibility to independently determine suitability

of any products and to test and verify the same. The information provided by Microsemi hereunder is provided “as is, where is” and with all faults, and the entire risk associated with such information is entirely with the Buyer.

Microsemi does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other IP rights, whether with regard to such information itself or anything described by such information. Information provided in

this document is proprietary to Microsemi, and Microsemi reserves the right to make any changes to the information in this document or to any products and services at any time without notice.

Highlights

• Virutal Service Aware Architecture (ViSAA™)

• Hardware-based Ethernet OAM, performance

monitoring, and Service Activation

Measurement (SAM)

• Network demarcation

• Hierarchical QoS priority for queuing and

subscriber separation

• Service protection (linear, ring)

Applications

• Microcell, femtocell, and picocell base stations

• Small cell backhaul systems

that offers an unmatched level of Service Edge and Carrier Ethernet (CE)

networking features. ViSAA achieves wirespeed performance for even

the most feature-rich Carrier Ethernet services. VSC7435 also integrates

VeriTime™, Microsemi's patent-pending timing technology that delivers

the industry’s most accurate IEEE 1588v2 time stamping. Combined with

PTP software and an advanced Servo algorithm, Microsemi offers the most

accurate 1588 solution

The VSC7435 Carrier Ethernet switch contains four 10/100/1000 Mbps

ports (up to two copper ports), and two 10/100/1000/2500 Mbps ports.

An integrated DPLL simplifi es system design, and provides proven

fl exible for secure applications. It features advanced TCAM classifi cation in

both ingress and egress. Per-EVC features include a rich set of statistics,

OAM for end-to-end performance monitoring, and dual-rate policing and

shaping.

VSC7435 supports IPv4/IPv6 Layer-3 (L3) routing and IPv4/IPv6 L3

multicast groups. L3 security features include source guard and unicast

Reverse path Forwarding (uRFP) tasks.

VSC7435 supports Microsemi's application programming interface for easy

integration with third-party application software. The device also supports

Microsemi's CEServices application software, dramatically reducing time-

Aggregation and Core

IP, MPLS, Ethernet, OTN

SONET/SDH, OTN

Over

Microwave (MW)

trademarks and service marks are the property of their respective owners.

Features

• 4 × 10/100/1000 ports (up to two copper), 2 ×

10/100/1000/2500 ports

• Integrated DPLL and integrated shared packet memory

• Fully nonblocking wire-speed switching performance for all

frame sizes

• 8 QoS classes with thousands of H-QoS queues

• Energy Effi cient Ethernet (EEE)

• Priority-based fl ow control

• Integrated MIPS-24KEc CPU with DDR3 SDRAM controller

• RSTP and MSTP support

• Hardware- and software-based learning

• Link aggregation (IEEE 802.3ad)

• Independent and shared VLAN learning (IVL, SVL)

• Jumbo frame support

Layer 3 Routing

• 1K/256 IPv4/IPv6 table entries (LPM and hosts)

• 512/256 IPv4/IPv6 (S, G, V) or (*, G, V) multicast groups

• Simultaneous L3 routing with Provider Bridging and MPLS/

MPLS-TP service switching

ViSAA™ and Carrier Ethernet Features

• Provider bridging (Q-in-Q) and MPLS/MPLS-TP

• Linear and ring protection switching

• MEF CE 2.0 ready: 8 COS EVCs with per-EVC dual-rate

policing and shaping, queueing, and statistics

• Advanced security and per-service classifi cation available

through multistage TCAM engines

• Hardware-based Ethernet and MPLS-TP OAM: up-MEPs and

down-MEPs, four layers of nested MEPs

• Hardware-based Y.1564 service activation test