SPECIFICATION
MODEL APV-25-5
APV-25-12
APV-25-15
APV-25-24
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
OUTPUT
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
Note.6
HOLD UP TIME (Typ.)
VOLTAGE RANGE
Note.4
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT
INPUT
INRUSH CURRENT(Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
5V
12V
15V
24V
3.5A
2.1A
1.68A
1.05A
0 ~ 3.5A
0 ~ 2.1A
0 ~ 1.68A
0 ~ 1.05A
17.5W
25.2W
25.2W
25.2W
120mVp-p
150mVp-p
150mVp-p
150mVp-p
±5.0%
±1.0%
±2.0%
1500ms, 30ms / 230VAC 1500ms,30ms / 115VAC at full load
90 ~ 264VAC 127 ~ 370VDC
47 ~ 63Hz
75.5%
82%
83%
83%
5.75 ~ 6.95V
13.8 ~ 16.2V
17.25 ~ 21V
27 ~ 32.4V
0.4A/230VAC 0.8A/115VAC
COLD START 45A(twidth=310 s measured at 50% Ipeak) at 230VACμ
0.25mA / 240VAC
Protection type : Hiccup mode, recovers automatically after fault condition is removed
20 ~ 90% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
84*57*29.5mm (L*W*H)
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Derating may be needed under low input voltage. Please check the static characteristics for more details.
5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
6. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
7.The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit.
25W Single Output Switching Power Supply
Constant voltage mode power supply
Universal AC input / Full range
Withstand 300VAC Surge input for 5 seconds
Protections: Short circuit / Over load / Over voltage
Fully isolated plastic case
Cooling by free air convection
Small and compact size
IP42 design
Class 2 power unit
ass LPSP
100% full load burn-in test
Low cost, high reliability
Suitable for LED related fixture or appliance
(such as LED Decoration or Advertisement devices)
2 years warranty
■
Features :
APV-25 series
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ENVIRONMENT
SAFETY &
EMC
PROTECTION
20ms/230VAC 12ms/115VAC at full load
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC
I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH℃
File Name:APV-25-SPEC 2018-01-08
LPS
692.8K hrs min. MIL-HDBK-217F (25 )℃
EMC IMMUNITY
Compliance to EN55032,EN61000-3-2 Class A,EN61000-3-3, EAC TP TC 020
Compliance to EN55024,EN61000-4-2,3,4,5,6,8,11; light industry level(surge 2KV), criteria A, EAC TP TC 020
EMC EMISSION
APV-25-36
36V
0.7A
0 ~ 0.7A
25.2W
150mVp-p
84%
41.4 ~ 48.6V
-30 ~ 70 (Refer to "Derating Curve")℃
Above 105% rated output power
Protection type : Shut down o/p voltage, re-power on to recover
0.13Kg; 72pcs / 10.4Kg / 0.92CUFT
UL8750 , CSA-C22.2 No. 250.0-13, BIS IS15885(except for 15V,36V), EAC TP TC 004,IP42 approved; design refer to EN60950-1
MAX. No. of PSUs on 16A
CIRCUIT BREAKER
9 units (circuit breaker of type B) / 15 units (circuit breaker of type C) at 230VAC
IP42
IS 15885(Part 2/Sec13)
R-41027766
THOMAS SAMUEL
THOMAS SAMUEL
(except for 15V,36V)
