OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

HFA1109IBZ96

P1-P3P4-P6P7-P9P10-P12
1
®
FN4019.5
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774
| Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 1999, 2004, 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
HFA1109
450MHz, Low Power, Current Feedback
Video Operational Amplifier
The HFA1109 is a high speed, low power, current feedback
amplifier built with Intersil’s proprietary complementary
bipolar UHF-1 process. This amplifier features a unique
combination of power and performance specifically tailored
for video applications.
The HFA1109 is a standard pinout op amp. It is a higher
performance, drop-in replacement (no feedback resistor
change required) for the CLC409.
If a comparably performing op amp with an output disable
function (useful for video multiplexing) is required, please
refer to the HFA1149 data sheet..
Features
• Wide - 3dB Bandwidth (A
V
= +2) . . . . . . . . . . . . . 450MHz
• Gain Flatness (To 250MHz) . . . . . . . . . . . . . . . . . . . 0.8dB
• Very Fast Slew Rate (A
V
= +2). . . . . . . . . . . . . . 1100V/μs
• High Input Impedance . . . . . . . . . . . . . . . . . . . . . . 1.7MΩ
• Differential Gain/Phase . . . . . . . . . . . . . . . . . 0.02%/0.02°
• Low Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
• Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
• Professional Video Processing
• Video Switchers and Routers
• Medical Imaging
• PC Multimedia Systems
• Video Distribution Amplifiers
• Flash Converter Drivers
• Radar/IF Processing
Pinout
HFA1109
(8 LD SOIC)
TOP VIEW
Ordering Information
PART
NUMBER
PART
MARKING
TEMP.
RANGE
(°C) PACKAGE
PKG.
DWG. #
HFA1109IB 1109IB -40 to +85 8 Ld SOIC (150MIL) M8.15
HFA1109IBZ
(Note 1)
HFA1109
IBZ
-40 to +85 8 Ld SOIC (150MIL)
(Pb-free)
M8.15
HFA1109IBZ96
(Note 1)
HFA1109
IBZ
-40 to +85 8 Ld SOIC (150MIL)
(Pb-free)
M8.15
HFA11XXEVAL
(Note 2)
DIP Evaluation Board for High Speed Op Amps
NOTES:
1. Intersil Pb-free plus anneal products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
2. Requires a SOIC-to-DIP adapter. See “Evaluation Board” section
inside.
NC
-IN
+IN
V-
1
2
3
4
8
7
6
5
NC
V+
OUT
NC
+
-
Data Sheet April 23, 2007
2
FN4019.5
April 23, 2007
Absolute Maximum Ratings Thermal Information
Voltage Between V+ and V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V
DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
SUPPLY
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8V
Output Current (Note 4) . . . . . . . . . . . . . . . . .Short Circuit Protected
30mA Continuous
60mA ≤ 50% Duty Cycle
ESD Rating
Human Body Model (Per MIL-STD-883 Method 3015.7) . . . .1400V
Charged Device Model (Per EOS/ESD DS5.3, 4/14/93) . . . .2000V
Machine Model (Per EIAJ ED-4701Method C-111) . . . . . . . . . .50V
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Thermal Resistance (Typical, Note 3) θ
JA
(°C/W)
8 Lead SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Maximum Junction Temperature (Die). . . . . . . . . . . . . . . . . . +175°C
Maximum Junction Temperature (Plastic Package) . . . . . . . +150°C
Maximum Storage Temperature Range. . . . . . . . . -65°C to +150°C
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. θ
JA
is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See
Tech Brief TB379.
4. Output is short circuit protected to ground. Brief short circuits to ground will not degrade reliability, however continuous (100% duty cycle) output
current must not exceed 30mA for maximum reliability.
Electrical Specifications V
SUPPLY
= ±5V, A
V
= +2, R
F
= 250Ω, R
L
= 100Ω, Unless Otherwise Specified.
PARAMETER TEST CONDITIONS
(NOTE 5)
TEST
LEVEL TEMP. (°C) MIN TYP MAX UNITS
INPUT CHARACTERISTICS
Input Offset Voltage A 25 - 1 5 mV
AFull-28mV
Average Input Offset Voltage Drift B Full - 10 - μV/°C
Input Offset Voltage
Common-Mode Rejection Ratio
DV
CM
= ±2V A 25 47 50 - dB
A Full 45 48 - dB
Input Offset Voltage
Power Supply Rejection Ratio
DV
PS
= ±1.25V A 25 50 53 - dB
A Full 47 51 - dB
Non-Inverting Input Bias Current A 25 - 4 10 μA
AFull-515μA
Non-Inverting Input Bias Current Drift B Full - 30 - nA/°C
Non-Inverting Input Bias Current
Power Supply Sensitivity
DV
PS
= ±1.25V A 25 - 0.5 1 μA/V
A Full - 0.5 3 μA/V
Inverting Input Bias Current A 25 - 2 10 μA
AFull-315μA
Inverting Input Bias Current Drift B Full - 40 - nA/°C
Inverting Input Bias Current
Common-Mode Sensitivity
DV
CM
= ±2V A 25 - 3 6 μA/V
AFull-38μA/V
Inverting Input Bias Current
Power Supply Sensitivity
DV
PS
= ±1.25V A 25 - 1.6 5 μA/V
A Full - 1.6 8 μA/V
Non-Inverting Input Resistance DV
CM
= ±2V A 25, 85 0.8 1.7 - MΩ
A -40 0.5 1.4 - MΩ
Inverting Input Resistance B 25 - 60 - Ω
HFA1109
3
FN4019.5
April 23, 2007
Input Capacitance B 25 - 1.6 - pF
Input Voltage Common Mode Range
(Implied by V
IO
CMRR, +R
IN
, and -I
BIAS
CMS
tests)
AFull±2±2.5 - V
Input Noise Voltage Density (Note 6) f = 100kHz B 25 - 4 - nV/√Hz
Non-Inverting Input Noise Current Density
(Note 4)
B 25 - 2.4 - pA/√Hz
Inverting Input Noise Current Density
(Note 4)
f = 100kHz B 25 - 40 - pA/√Hz
TRANSFER CHARACTERISTICS
Open Loop Transimpedance Gain (Note 6) B 25 - 500 - kΩ
Minimum Stable Gain B Full - 1 - V/V
AC CHARACTERISTICS
-3dB Bandwidth
(V
OUT
= 0.2V
P-P
, Note 6)
A
V
= -1, R
F
= 200Ω B 25 300 375 - MHz
B Full 290 360 - MHz
A
V
= +1, +R
S
= 550Ω (PDIP),
+R
S
= 700Ω (SOIC)
B 25 280 330 - MHz
B Full 260 320 - MHz
A
V
= +2 B 25 390 450 - MHz
B Full 350 410 - MHz
Gain Peaking A
V
= +2, V
OUT
= 0.2V
P-P
B25-00.2dB
B Full - 0 0.5 dB
Gain Flatness
(A
V
= +2, V
OUT
= 0.2V
P-P
, Note 6)
To 125MHz B 25 -1.0 -0.45 - dB
B Full -1.1 -0.45 - dB
To 200MHz B 25 -1.6 -0.75 - dB
B Full -1.7 -0.75 - dB
To 250MHz B 25 -1.9 -0.85 - dB
B Full -2.2 -0.85 - dB
Gain Flatness
(A
V
= +1, +R
S
= 550Ω (PDIP),
+R
S
= 700Ω (SOIC), V
OUT
= 0.2V
P-P
,
(Note 6)
To 125MHz B 25 ±0.3 ±0.1 - dB
BFull±0.4 ±0.1 - dB
To 200MHz B 25 ±0.8 ±0.35 - dB
BFull±0.9 ±0.35 - dB
To 250MHz B 25 ±1.3 ±0.6 - dB
BFull±1.4 ±0.6 - dB
OUTPUT CHARACTERISTICS
Output Voltage Swing, Unloaded
(Note 6)
A
V
= -1, R
L
= Infinity A 25 ±3±3.2 - V
AFull±2.8 ±3 - V
Output Current
(Note 6)
A
V
= -1, R
L
= 75Ω A 25, 85 ±33 ±36 - mA
A-40±30 ±33 - mA
Output Short Circuit Current A
V
= -1 B 25 - 120 - mA
Closed Loop Output Resistance (Note 6) DC, A
V
= +1 B 25 - 0.05 - W
Electrical Specifications V
SUPPLY
= ±5V, A
V
= +2, R
F
= 250Ω, R
L
= 100Ω, Unless Otherwise Specified. (Continued)
PARAMETER TEST CONDITIONS
(NOTE 5)
TEST
LEVEL TEMP. (°C) MIN TYP MAX UNITS
HFA1109
P1-P3P4-P6P7-P9P10-P12

HFA1109IBZ96

Mfr. #:
Buy HFA1109IBZ96
Manufacturer:
Renesas / Intersil
Description:
Operational Amplifiers - Op Amps W/ANNEAL OPAMP 450MHZ CFB IND
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet