CR2512-JW-300ELF Datasheet CR2010-FX-1211ELF, CR2010-JW-911ELF, CR2512-JW-153ELF | P1-P3

Features

n RoHS compliant*

n Power rating at 70 °C: CR2010 - 1/2 W,

CR2512 - 1 W

n Tight tolerances of bottom electrode width

n Three layer termination process with nickel

barrier prevents leaching and provides

excellent solderability

n Suitable for most types of soldering

processes

n Standard packaging on tape and reel

n AEC-Q200 approval upon request

CR2010/CR2512 - Chip Resistors

*RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011.

Speciﬁcations are subject to change without notice.

The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.

Users should verify actual device performance in their speciﬁc applications.

Derating Curve

*RoHS COMPLIANT

LEAD FREE

*RoHS COMPLIANT

VERSIONS

AVAILABLE

LEAD FREE

VERSIONS ARE

RoHS COMPLIANT*

DIMENSIONS:

(INCHES)

Electrical Characteristics

Model Model

Characteristic CR2010 CR2512

Power Rating @ 70 °C 1/2 W 1 W

Operating Temperature Range -55 °C to +155 °C

Derated to 0 Load at +155 °C

Maximum Working Voltage 200 V

Maximum Overload Voltage 400 V

Resistance Range: 1 % 10 ohms ≤ R ≤ 1M ohms

E-96 + E-24 ±100 PPM/°C

1M ohms < R ≤ 10M ohms

±200 PPM/°C

Resistance Range: 5 % 10 ohms ≤ R ≤ 10M ohms

E-24 ±200 PPM/°C

1 ohm ≤ R < 10 ohms

10M ohms < R ≤ 20M ohms

±400 PPM/°C

Zero Ohm Jumper <0.05 ohm

Rated/Maximum Current

2 A/5 A 2 A/5 A

For Standard Values Used in Capacitors,

Inductors, and Resistors, click here.

Chip Dimensions

Dimension Model Model

CR2010 CR2512

5.00 ± 0.20 6.30 ± 0.20

(0.197 ± 0.008) (0.248 ± 0.008)

2.50 ± 0.20 3.10 ± 0.20

(0.098 ± 0.008) (0.122 ± 0.008)

0.60 ± 0.10 0.60 ± 0.15

(0.024 ± 0.004) (0.024 ± 0.006)

0.60 ± 0.25 0.60 ± 0.25

(0.024 ± 0.010) (0.024 ± 0.010)

0.60 ± 0.25 0.60 ± 0.25

(0.024 ± 0.010) (0.024 ± 0.010)

Dimensional Drawing

Dimensional Drawings

100

Rated Power (%)

Ambient Temperature (°C)

-55

070

155

Performance Characteristics

Test Procedure Method

Test Limits DR

1 % 5 %

Thermal Shock

-55 ℃ for 30 minutes, +155 ℃ for 30 minutes,

5 cycles

IEC60115-1-4.19 ≤±(0.5 % + 0.05 Ω) ≤±(1 % + 0.05 Ω)

Short Time Overload 2.5 X rated voltage for 5 seconds IEC60115-1-4.13 ≤±(1 % + 0.05 Ω)

Resistance to Solder Heat 270 ±5 ℃ for 10 ±1 seconds IEC60115-1-4.18 ≤±(0.5 % + 0.05 Ω) ≤±(1 % + 0.05 Ω)

Resistance to Dry Heat 125 ±5 ℃ for 96 ±4 hours IEC60115-1-4.23.2 ≤±(1 % + 0.05 Ω) ≤±(2 % + 0.1 Ω)

Load Life

Rated voltage for 1000 hours, 70 ℃,

1.5 hours “ON“, 0.5 hours “OFF”

IEC60115-1-4.25.1 ≤±(1 % + 0.05 Ω) ≤±(3 % + 0.1 Ω)

Load Life with Humidity

Rated voltage for 1000 hours, 40 ±2 ℃,

90~95 % RH, 1.5 hours “ON“, 0.5 hours “OFF”

IEC60115-1-4.24 ≤±(1 % + 0.05 Ω) ≤±(3 % + 0.1 Ω)

Solderability 245 ±5 ℃, 2 ±0.5 seconds IEC60115-1-4.17 ≥95 % of area covered

Bending 3 mm IEC60115-1-4.33 ≤±(0.5 % + 0.05 Ω) ≤±(1 % + 0.05 Ω)

Dielectric Withstanding

Voltage

-- IEC60115-1-4.7 >500 V

Insulation Resistance 100 V IEC60115-1-4.6 ≥1 GΩ

222

Speciﬁcations are subject to change without notice.

The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.

Users should verify actual device performance in their speciﬁc applications.

CR2010/CR2512 - Chip Resistors

Soldering Prole for RoHS Compliant Chip Resistors and Arrays

125

175

225

275

050 100 150 200 250 300

Time (seconds)

Temperature (°C)

60 - 120 seconds

60 - 90

seconds

260 °C peak

190 °C

150 °C

220 °C

Ramp Down

6 °C/second

255 °C

Maximum of 20 seconds between

+255 °C and +260 °C

Ramp Up

3 °C/second maximum

10 seconds minimum

<1>

Marking Explanation

Resistors with 5 % tolerance may have a

3-digit or 4-digit resistance code.

Complete information about resistance

value and tolerance is found on the label

of the reel of chip resistors.

• 5 %: 3 digits, rst two digits are

signicant, third digit is number of

zeros to follow. Letter R is decimal point

for values from 1 to 9.9 ohms.

• 5 %: 4 digits, rst three digits are

signicant, fourth digit is number of

zeros to follow. Letter R is decimal point

for values from 1 to 99.9 ohms.

• 1 %: 4 digits, rst three digits are

signicant, fourth digit is number of

zeros to follow. Letter R is decimal for

values from 1 to 99.9 ohms.

How to Order

CR 2010 - F X - 8252 E LF

Model

(CR = Chip Resistor)

Size

• 2010

• 2512

Resistance Tolerance

F = ±1 % .............. Use with “X” TCR code only for values from 10 ohms through 1 megohm;

Use with “W” TCR code only for values from 1 megohm through 10 megohms

J = ±5 % .................Use with “W” TCR code for values from 10 ohms through 10 megohms;

Use with “Z” TCR code for values above 10 megohms through 20 megohms;

Use with “/” TCR code for zero ohm (jumper) and values from 1 ohm through 9.1 ohms.

TCR (ppm/°C)

X = ±100

W = ±200

Z = ±400

/ = Used with “J” Resistance Tolerance code for zero ohm (jumper) and values from 1 ohm through 9.1 ohms.

Resistance Value

For 1 % Tolerance:

<100 ohms...............“R” represents decimal point (example: 24R3 = 24.3 ohms)

≥100 ohms ...............First three digits are signicant, fourth digit represents number of zeros to follow (example: 8252 = 82.5k W)

For 5 % Tolerance:

<10 ohms .............. “R” represents decimal point (example: 4R7 = 4.7 ohms)

≥10 ohms ............... First two digits are signicant, third digit represents number of zeros to follow (example: 474 = 470k ohms; 000 = Jumper)

Packaging

E = Embossed Plastic Tape (4,000 pcs.) on 7 ” Plastic Reel

Termination

LF = Tin-plated (RoHS compliant)

3312 - 2 mm SMD Trimming Potentiometer

Speciﬁcations are subject to change without notice.

The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time.

Users should verify actual device performance in their speciﬁc applications.

CR2010/CR2512 - Chip Resistors

Packaging Dimensions

REV. 07/15

DIMENSIONS:

(INCHES)

1.5 +0.1/-0

(.056 + .004/-0)

1.75 ± 0.1

(.059 ± .004)

4.0 ± 0.1

(.157 ± .004)

2.0 ± 0.05

(.079 ± .002)

Dimension

Model Model

CR2010 CR2512

2.8 ± 0.2 3.5 ± 0.2

(0.110 ± 0.008) (0.138 ± 0.008)

5.5 ± 0.2 6.7 ± 0.2

(0.217 ± 0.008) (0.264 ± 0.008)

12.0 ± 0.3 12.0 ± 0.3

(0.472 ± 0.012) (0.472 ± 0.012)

5.5 ± 0.05 5.5 ± 0.05

(0.217 ± 0.002) (0.217 ± 0.002)

4.0 ± 0.1 4.0 ± 0.1

(0.157 ± 0.004) (0.157 ± 0.004)

2.0 ± 0.5

(.080 ± .020)

178.0 ± 2.0

(7.008 ± .080)

20.0

(.787)

MIN.

16.7

(.657)

MAX.

13.0 ± 0.5

(.512 ± .020)

80.0 ± 0.5

(3.150 ± .020)

P1-P3

CR2512-JW-300ELF

Mfr. #:

Buy CR2512-JW-300ELF

Manufacturer:

Bourns

Description:

Thick Film Resistors - SMD 30OHM 1WATT 5%

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

CR2512-JW-300ELF

CR2512-JW-300ELF

Products related to this Datasheet