PDF: 09005aef8092973f / Source: 09005aef80921669 Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD8C32_64x64H.fm - Rev. D 9/08 EN
11 ©2004 Micron Technology, Inc. All rights reserved.
256MB, 512MB (x64, SR) 200-Pin DDR SDRAM SODIMM
Electrical Specifications
Table 10: IDD Specifications and Conditions – 256MB (All Other Die Revisions)
Values are for the MT46V32M8 DDR SDRAM only and are computed from values specified in the
256Mb (32 Meg x 8) component data sheet
Parameter/Condition Symbol -40B -335 -262 -26A -265 Units
Operating one bank active-precharge current:
t
RC =
t
RC (MIN);
t
CK =
t
CK (MIN); DQ, DM, and DQS inputs
changing once per clock cycle; Address and control inputs
changing once every two clock cycles
IDD0 1,080 1,000 1,000 960 960 mA
Operating one bank active-read-precharge current: BL = 4;
t
RC =
t
RC (MIN);
t
CK =
t
CK (MIN); IOUT = 0mA; Address and
control inputs changing once per clock cycle
IDD1 1,360 1,360 1,280 1,160 1,160 mA
Precharge power-down standby current: All device banks
idle; Power-down mode;
t
CK =
t
CK (MIN); CKE = LOW
IDD2P 32 32 32 32 32 mA
Idle standby current: CS# = HIGH; All device banks idle;
t
CK =
t
CK (MIN); CKE = HIGH; Address and other control inputs
changing once per clock cycle; V
IN
=V
REF
for DQ, DM, and DQS
IDD2F 480 400 360 360 360 mA
Active power-down standby current: One device bank
active; Power-down mode;
t
CK =
t
CK (MIN); CKE = LOW
IDD3P 320 240 200 200 240 mA
Active standby current: CS# = HIGH; CKE = HIGH; One device
bank active;
t
RC =
t
RAS (MAX);
t
CK =
t
CK (MIN); DQ, DM, and
DQS inputs changing twice per clock cycle; Address and other
control inputs changing once per clock cycle
IDD3N 560 480 400 400 400 mA
Operating burst read current: BL = 2; Continuous burst reads;
One device bank active; Address and control inputs changing
once per clock cycle;
t
CK =
t
CK (MIN); IOUT =0mA
IDD4R 1,600 1,400 1,200 1,200 1,200 mA
Operating burst write current: BL = 2; Continuous burst
writes; One device bank active; Address and control inputs
changing once per clock cycle;
t
CK =
t
CK (MIN); DQ, DM, and
DQS inputs changing twice per clock cycle
IDD4W 1,560 1,400 1,200 1,200 1,200 mA
Auto refresh current
t
RFC =
t
RFC (MIN)
IDD5 2,080 2,040 1,880 1,880 1,960 mA
t
RFC = 7.8125µs
IDD5A 48 48 48 48 48 mA
Self refresh current: CKE ≤ 0.2V
IDD63232323232mA
Operating bank active interleave read current: Four device
bank interleaving reads (BL = 4) with auto precharge;
t
RC =
t
RC (MIN);
t
CK =
t
CK (MIN); Address and control inputs
change only during active READ or WRITE commands
IDD7 3,760 3,280 2,800 2,800 2,920 mA