0603ZZ105KAT2A Datasheet 0603ZZ105MAT2A, 04026Z104KAT2A, 06036Z105KAT2A | P1-P3

090215

X7S formulations are called “temperature stable” ceramics and

fall into EIA Class II materials. Its temperature variation of

capacitance s within ±22% from –55°C to +125°C. This

capacitance change is non-linear.

Capacitance for X7S varies under the influence of electrical

operating conditions such as voltage and frequency.

X7S dielectric chip usage covers the broad spectrum of

industrial applications where known changes in capacitance due

to applied voltages are acceptable.

X7S Dielectric

General Specifications

PART NUMBER (see page 2 for complete part number explanation)

GENERAL DESCRIPTION

TYPICAL ELECTRICAL CHARACTERISTICS

1206

Size

(L" x W")

Voltage

4 = 4V

6 = 6.3V

Z = 10V

Y = 16V

3 = 25V

5 = 50V

1 = 100V

2 = 200V

Dielectric

Z = X7S

105

Capacitance

Code (In pF)

2 Sig. Digits +

Number of

Zeros

Capacitance

Tolerance

K = ±10%

M = ±20%

Failure

Rate

A = N/A

Terminations

T = Plated Ni

and Sn

Packaging

2 = 7" Reel

4 = 13" Reel

Special

Code

A = Std.

Product

% ⌬ Capacitance

+10

+20

+30

-10

-20

-30

1KHz

10 KHz 100 KHz 1 MHz 10 MHz

Frequency

⌬

Capacitance vs. Frequency

Insulation Resistance (Ohm-Farads)

1,000

10,000

100

120

40 60 80

Temperature °C

Insulation Resistance vs Temperature

100

Impedance, ⍀

100 1000

Frequency, MHz

Variation of Impedance with Cap Value

Impedance vs. Frequency

1,000 pF vs. 10,000 pF - X7S

0805

0.10

0.01

1.00

1,000 pF

10,000 pF

10.00

Impedance, ⍀

110

100 1,000

Frequency, MHz

Variation of Impedance with Chip Size

Impedance vs. Frequency

100,000 pF - X7S

0.1

.01

1.0

1206

0805

1210

Impedance, ⍀

110

100 1,000

Frequency, MHz

Variation of Impedance with Chip Size

Impedance vs. Frequency

10,000 pF - X7S

0.1

.01

1.0

1206

0805

1210

-5

-10

-15

-20

-25

-60 -40 -20 0 20 40

Temperature (°C)

% Cap Change

60 80 100 120 140

X7S Dielectric

Typical Temperature Coefficient

NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers.

090215

X7S Dielectric

Specifications and Test Methods

Parameter/Test X7S Specification Limits Measuring Conditions

Operating Temperature Range -55ºC to +125ºC Temperature Cycle Chamber

Capacitance Within specified tolerance

≤ 5.0% for ≥ 100V DC rating Freq.: 1.0 kHz ± 10%

Dissipation Factor

≤ 5.0% for ≥ 25V DC rating Voltage: 1.0Vrms ± .2V

≤ 10.0% for ≥ 10V DC rating For Cap > 10 μF, 0.5Vrms @ 120Hz

≤ 10.0% for ≤ 10V DC rating

Insulation Resistance

100,000MΩ or 1000MΩ - μF, Charge device with rated voltage for

whichever is less 120 ± 5 secs @ room temp/humidity

Charge device with 300% of rated voltage for

Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current

limited to 50 mA (max)

Appearance No defects Deflection: 2mm

Capacitance Test Time: 30 seconds

Resistance to Variation

≤ ±12%

Flexure Dissipation

Meets Initial Values (As Above)

Stresses Factor

Insulation

≥ Initial Value x 0.3

Resistance

Solderability

≥ 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC

with fresh solder for 5.0 ± 0.5 seconds

Appearance No defects, <25% leaching of either end terminal

Capacitance

Variation

≤ ±7.5%

Dip device in eutectic solder at 260ºC for 60

Dissipation

Meets Initial Values (As Above)

seconds. Store at room temperature for 24 ± 2

Resistance to

Factor

hours before measuring electrical properties.

Solder Heat

Insulation

Meets Initial Values (As Above)

Resistance

Dielectric

Meets Initial Values (As Above)

Strength

Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes

Capacitance

Variation

≤ ±7.5% Step 2: Room Temp ≤ 3 minutes

Dissipation

Meets Initial Values (As Above) Step 3: +125ºC ± 2º 30 ± 3 minutes

Thermal

Factor

Shock

Insulation

Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes

Resistance

Dielectric

Meets Initial Values (As Above)

Repeat for 5 cycles and measure after

Strength 24 ± 2 hours at room temperature

Appearance No visual defects

Capacitance

Variation

≤ ±12.5%

Dissipation

≤ Initial Value x 2.0 (See Above)

Load Life Factor

Insulation

≥ Initial Value x 0.3 (See Above)

Resistance

Dielectric

Meets Initial Values (As Above)

Strength

Appearance No visual defects

Capacitance

Variation

≤ ±12.5%

Load Dissipation

≤ Initial Value x 2.0 (See Above)

Humidity Factor

Insulation

≥ Initial Value x 0.3 (See Above)

Resistance

Dielectric

Meets Initial Values (As Above)

Strength

Charge device with 1.5 rated voltage (≤ 10V) in

test chamber set at 125ºC ± 2ºC

for 1000 hours (+48, -0)

Remove from test chamber and stabilize

at room temperature for 24 ± 2 hours

before measuring.

Store in a test chamber set at 85ºC ± 2ºC/

85% ± 5% relative humidity for 1000 hours

(+48, -0) with rated voltage applied.

Remove from chamber and stabilize at

room temperature and humidity for

24 ± 2 hours before measuring.

1mm/sec

90 mm

090215

X7S Dielectric

Capacitance Range

PREFERRED SIZES ARE SHADED

SIZE 0402 0603 0805 1206 1210

Soldering Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave Reflow Only

Packaging All Paper All Paper Paper/Embossed Paper/Embossed Paper/Embossed

(L) Length

mm 1.00 ± 0.10 1.60 ± 0.15 2.01 ± 0.20 3.20 ± 0.20 3.20 ± 0.20

(in.) (0.040 ± 0.004) (0.063 ± 0.006) (0.079 ± 0.008) (0.126 ± 0.008) (0.126 ± 0.008)

(W) Width

mm 0.50 ± 0.10 0.81 ± 0.15 1.25 ± 0.20 1.60 ± 0.20 2.50 ± 0.20

(in.) (0.020 ± 0.004) (0.032 ± 0.006) (0.049 ± 0.008) (0.063 ± 0.008) (0.098 ± 0.008)

(t) Terminal

mm 0.25 ± 0.15 0.35 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 0.50 ± 0.25

(in.) (0.010 ± 0.006) (0.014 ± 0.006) (0.020 ± 0.010) (0.020 ± 0.010) (0.020 ± 0.010)

WVDC 6.3 6.3 4 10 50 100 6.3

Cap 100

(pF) 150

220

330

470

680

1000

1500

2200

3300

4700

6800

Cap 0.010

(μF 0.015

0.022

0.033 C

0.047 C

0.068 C

0.10 C

0.15

0.22

0.33 G

0.47 G

0.68 G

1.0 G

1.5 N

2.2 N

3.3 N

4.7 N Q Q*

22 Z

100

WVDC 6.3 6.3 4 10 50 100 6.3

SIZE 0402 0603 0805 1206 1210

䉲

Letter ACEGJKMNPQXYZ

Max. 0.33 0.56 0.71 0.90 0.94 1.02 1.27 1.40 1.52 1.90 2.29 2.54 2.79

Thickness (0.013) (0.022) (0.028) (0.035) (0.037) (0.040) (0.050) (0.055) (0.060) (0.075) (0.090) (0.100) (0.110)

PAPER EMBOSSED

*Contact Factory for Specifications

P1-P3

0603ZZ105KAT2A

Mfr. #:

Buy 0603ZZ105KAT2A

Manufacturer:

N/A

Description:

Multilayer Ceramic Capacitors MLCC - SMD/SMT 10volts 1uF 10% X7S

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

0603ZZ105KAT2A

0603ZZ105KAT2A

Products related to this Datasheet