15
INDUSTRIAL TEMPERATURE RANGE
IDT5T9820
EEPROM PROGRAMMABLE 2.5V ZERO DELAY PLL CLOCK DRIVER
SINGLE-ENDED INPUT AC TEST CONDITIONS FOR 2.5V LVTTL
Symbol Parameter Value Units
VIH Input HIGH Voltage VDD V
VIL Input LOW Voltage 0V
VTHI Input Timing Measurement Reference Level
(1)
VDD/2 V
t
R, tF Input Signal Edge Rate
(2)
2 V/ns
NOTES:
1. A nominal 1.25V timing measurement reference level is specified to allow constant, repeatable results in an automatic test equipment (ATE) environment.
2. The input signal edge rate of 2V/ns or greater is to be maintained in the 10% to 90% range of the input waveform.
DIFFERENTIAL INPUT AC TEST CONDITIONS FOR 2.5V LVTTL
Symbol Parameter Value Units
VDIF Input Signal Swing
(1)
VDD V
VX Differential Input Signal Crossing Point
(2)
VDD/2 V
VTHI Input Timing Measurement Reference Level
(3)
Crossing Point V
tR, tF Input Signal Edge Rate
(4)
2.5 V/ns
NOTES:
1. A nominal 2.5V peak-to-peak input pulse level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VDIF
(AC) specification under actual use conditions.
2. A nominal 1.25V crossing point level is specified to allow consistent, repeatable results in an automatic test equipment (ATE) environment. This device meets the VX specification
under actual use conditions.
3. In all cases, input waveform timing is marked at the differential cross-point of the input signals.
4. The input signal edge rate of 2.5V/ns or greater is to be maintained in the 20% to 80% range of the input waveform.
POWER SUPPLY CHARACTERISTICS FOR 2.5V LVTTL OUTPUTS
(1)
Symbol Parameter Test Conditions
(2)
Typ. Max Unit
I
DDQ Quiescent VDD Power Supply Current
(3)
VDDQN = Max., REF = LOW, PD = HIGH, nSOE = LOW, 112 150 mA
PLL_EN = HIGH, Outputs enabled, All outputs unloaded
I
DDQQ Quiescent VDDQN Power Supply Current
(3)
VDDQN = Max., REF = LOW, PD = HIGH, nSOE = LOW, 20 75 µA
PLL_EN = HIGH, Outputs enabled, All outputs unloaded
IDDPD Power Down Current VDD = Max., PD = LOW, nSOE = LOW, PLL_EN = HIGH 0.7 3 mA
I
DDD Dynamic VDD Power Supply VDD = Max., VDDQN = Max., CL = 0pF 19 30 µA/MHz
Current per Output
I
DDDQ Dynamic VDDQN Power Supply VDD = Max., VDDQN = Max., CL = 0pF 32 40 µA/MHz
Current per Output
I
TOT Total Power VDD Supply Current
(4,5)
VDDQN = 2.5V., FVCO = 100MHz, CL = 15pF 275 400 mA
VDDQN = 2.5V., FVCO = 250MHz, CL = 15pF 315 450
I
TOTQ Total Power VDDQN Supply Current
(4,5)
VDDQN = 2.5V., FVCO = 100MHz, CL = 15pF 215 320 mA
V
DDQN = 2.5V., FVCO = 250MHz, CL = 15pF 355 530
NOTES:
1. These power consumption characteristics are for all the valid input interfaces and cover the worst case input and output interface combinations.
2. The termination resistors are excluded from these measurements.
3. If the differential input interface is used, the true input is held LOW and the complementary input is held HIGH.
4. Bit 60 = 1.
5. All outputs are at the same interface level.