OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

RACD20-350-LP

P1-P3P4-P4
L-1
REV.: 0/2016www.recom-power.com
20 Watt
Constant
Current
Single
Output
AC/DC Converter
Features
LED
Driver
• Low Profile Case (13mm height max.)
• 350mA to 700mA Constant Current Outputs
• Terminal Block Input/Output with Cable Clamps
• Fully Protected (OLP, SCP, OCP, OTP)
• Suitable for Class I and Class II Luminaires
• low cost
RACD20-LP
Description
These low profile constant current LED drivers have been designed for cost-sensitive applications.
The SELV outputs are suitable for both independently supplied or built-in power-supply LED luminaires.
Their low profile design allows them to be invisibly built into furniture, discreetly mounted under shelves
or integrated in space-restricted applications such as coving lighting, strip lighting or troffer lighting sys-
tems. The power supplies are short circuit and overload protected and come with a full 3-year warranty.
Selection Guide
Part nom. Input Input Output Output Efficiency Output
Number Voltage Current Voltage Range Current typ. Power max.
[VAC] [mA] [VDC] [mA] [%] [W]
RACD20-350-LP 230 210 2-59 350 86 21W
RACD20-500-LP 230 210 2-40 500 85 20W
RACD20-700-LP 230 210 2-31 700 85 22W
3
Y
E
A
R
w
a
r
r
a
n
t
y
3
Specifications (measured @ ta= 25°C, 240VAC and rated load)
All LED Drivers may not be used without a load. They must be switched on the primary side only.
Noncompliance may damage the LED or reduce its lifetime.
BASIC CHARACTERISTICS
Parameter Condition Min. Typ. Max.
Input Voltage Range 198VAC 230VAC 264VAC
Inrush Current 8.0A
Start-up Time 500ms
Input Frequency Range 47Hz 63Hz
No Load Power Consumption 0.5W
Power Factor full load, 230VAC 0.55
Internal Operating Frequency full load 45kHz 140kHz
Output Ripple Current
(1)
50mAp-p
REGULATIONS
Parameter Condition Value
Output Current Accuracy ±5% max.
Line Regulation 5% max.
Load Regulation 5% max.
Notes:
Note1: Measured at 20MHz BW using 0.1µF & 47µF parallel capacitor.
ERP
compliant
IEC/EN61347-1 Certified
IEC/EN61347-2-13 Certified
ENEC Certified
CB Report
EN55015 Compliant
PROTECTION
Parameter Condition Value
Input Fuse external fuse is recommended T1A
Open Circuit Protection (OCP)
auto recovery after fault condition is removed
Over Load Protection (OLP)
auto recovery after fault condition is removed
Over Voltage Protection (OVP)
auto recovery after fault condition is removed
Over Temperature Protection (OTP) 110°C Tcase
auto recovery after fault condition is removed
Isolation Voltage I/P to O/P 3.75kVAC / 1 minute
AC/DC Converter
L-2
REV.: 0/2016 www.recom-power.com
Specifications (measured @ ta= 25°C, 240VAC and rated load)
RACD20-LP
Series
ENVIRONMENTAL
Parameter Condition
Value
Operating Temperature Range -20°C to +45°C, Ambient
Max. Case Temperature +85°C
Operating Altitude 2000m
Operating Humidity 5% to 85% RH, non condensing
IP Rating IP20
Pollution Degree PD2
Design Lifetime 30 x 10³ hours
Derating Graph
-20 605040
45
3020100-10
0
20
40
60
80
100
Ambient Temperature [°C]
Output Current [%]
Maximum loading of automatic circuit breakers
@ 230VAC, 1Ohm, 90° phase angle and max. load
Circuit Breaker Circuit Breaker Current
Typ 10A 16A 20A 25A
B 11 18 23 29
C 24 39 49 61
SAFETY AND CERTIFICATIONS
Certificate Type Report Number Standard
Lamp Controlgear General Requirments for Safety
305987
+
305985
IEC61347-1, 2nd Edition, 2012
EN61347-1, 2nd Edition 2013
Lamp Controlgear Particular Requirements
IEC61347-2-13, 2nd Edition, 2014
EN61347-2-13, 2014
D.C. or A.C. Controlgears for LED Performance Requirements 305984-1 + 305984-1 IEC/EN62384, 1st Edition, 2009
RoHS 2.1 LCS1606201548R RoHS-2011/65/EU + AM-2015/863
continued on next page
AC/DC Converter
L-3
REV.: 0/2016www.recom-power.com
RACD20-LP
Series
Specifications (measured @ ta= 25°C, 240VAC and rated load)
DIMENSION and PHYSICAL CHARACTERISTICS
Parameter
Type
Value
Material Case Plastic (UL94V-2)
Package Dimension (LxWxH) 128.0 x 50.0 x 13.0mm
Package Weight 75g
M3 Screws
50.0
50.0
FC 44.0
13.0
2.0
18.0
52.0
128.0
FC 115.0
tc
PRI
2
1
SEC
3
4
Mechanical Dimensions
2 mounting screws are included
wire preparation
6-7mm
EMI Compliance Standard / Criterion
Equipment for general Lighting Purpose - EMC Immunity Requirements
305984
+
305985
EN61547, 2009
Limits and methods of measurement of radio disturbance characteristics of electrical
lighting and similar equipment
EN55015, 2015
Assessment of lighting equipment related to human exposure to electromagnetic fields
EN61493, 2015
ESD Electrostatic discharge immunity test
±8kV Air Discharge,
±4kV Contact Discharge
EN61000-4-2, 2009, Criteria B
Radiated, radio-frequency, electromagnetic field immunity test 3V/m
EN61000-4-3, 2010, Criteria A
Fast Transient and Burst Immunity
±0.5kV (DC Output)
±1kV (AC Input)
EN61000-4-4, 2012, Criteria B
Surge Immunity ±0.5kV (AC Input) EN61000-4-5, 2014, Criteria C
Immunity to conducted disturbances, induced by radio-frequency fields 3V EN61000-4-6, 2014, Criteria A
Voltage Dips and Interuptions
95% reduction
30% reduction
EN61000-4-11, 2014, Criteria B
EN61000-4-11, 2014, Criteria C
Limits of Harmonic Current Emissions
EN61000-3-2, Class C, 2014
Voltage Fluctuations and Flicker in Public Low-Voltage Systems <=16A per phase
EN61000-3-3, 2013
Connection via Screw Terminal
# Function Solid Wire Stranded Wire
(2)
AWG
1 VAC in (N) 0.75-1.5mm² 0.75-1.5mm² 20-16
2 VAC in (L) 0.75-1.5mm² 0.75-1.5mm² 20-16
3 LED+ 0.5-1.5mm² 0.5-1.5mm² 21-16
4 LED- 0.5-1.5mm² 0.5-1.5mm² 21-16
wire stripping length: 6-7mm
recommended tightening torque: 0.25Nm
tc= case temperature measuring point
FC = fixing centers
NC= no connection
Tolerance: xx.x= ±0.5mm
xx.xx= ±0.35mm
Notes:
Note2: The use of sleeve or ferrule terminations is recommended.
P1-P3P4-P4

RACD20-350-LP

Mfr. #:
Buy RACD20-350-LP
Manufacturer:
RECOM Power
Description:
LED Power Supplies 21W 230Vin 2-59Vout 350mA
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet