135D
www.vishay.com
Vishay
Revision: 10-Jun-16
1
Document Number: 40024
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Wet Tantalum Capacitors Tantalum-Case with Glass-to-Tantalum
Hermetic Seal for -55 °C to +200 °C Operation
PERFORMANCE CHARACTERISTICS
Operating Temperature: -55 °C to +85 °C
(to +200 °C with voltage derating)
Capacitance Tolerance: at 120 Hz, +25 °C
± 20 % standard. ± 10 %, ± 5 % available as special.
DC Leakage Current (DCL Max.): at +25 °C and above:
leakage current shall not exceed the values listed in the
Standard Ratings table.
Life Test: capacitors are capable of withstanding a 2000 h
life test at a temperature of +85 °C or +125 °C at the
applicable rated DC working voltage.
Following life test:
1. DCL, measured at +85 °C rated voltage, shall not be in
excess of the original requirement.
2. The equivalent series resistance shall not exceed 150 %
of the initial requirement.
3. Change in capacitance shall not exceed 10 % from the
initial measurement.
FEATURES
• Axial through-hole terminations: standard tin /
lead (SnPb), 100 % tin (RoHS-compliant)
available
• Standard and extended ratings
• Model 135D tantalum-case electrolytic
capacitors incorporate the advantages of all
the varieties of electrolytic capacitors and
eliminate most of the disadvantages. These
units have a 3 V reverse voltage capability at
+85 °C and a higher ripple current capability
than any other electrolytic type with similar combinations
of capacitance and case size.
• Designed for the aerospace applications, this capacitor
was developed under partial sponsorship of the Marshall
Space Flight Center, National Aeronautics and Space
Administration. The capacitors have a high resistance to
damage from shock and vibration. Extended range ratings
and high temperature designs are available.
• Model 135D capacitors are commercial equivalents of
Tansitor style; AQ, AR, HAQ, HAR, Mallory-NACC Style;
TLT, TXT, THT, THX and Military Style CLR79 and CLR81,
designed to meet the performance requirements of
Military Specification MIL-PRF-39006/22/25. Capacitors
to meet MIL-PRF-39006/22/25 should be ordered by part
numbers shown in that specification.
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Note
*
This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
Please see the information / tables in this datasheet for details.
Note
• Packaging: the use of formed plastic trays for packaging these axial lead components is standard. Tape and reel is not available due to the
unit weight.
Available
Available
Available
ORDERING INFORMATION
135D 306 X0 006 C 2 E3
MODEL CAPACITANCE CAPACITANCE
TOLERANCE
DC VOLTAGE RATING
AT +85 °C
CASE
CODE
STYLE NUMBER RoHS-
COMPLIANT
This is expressed
in picofarads. The
first two digits are
the significant
figures. The third
is the number of
zeros to follow.
X0 = ± 20 %
X9 = ± 10 %
X5 = ± 5 %
This is expressed in
volts. To complete the
three-digit block,
zeros precede the
voltage rating.
See
Ratings
and
Case
Codes
table
Standard temperature
(max. +125 °C)
0 = no insulating sleeve
2 = polyester insulation sleeve
3 = high temperature
film insulation
High temperature
(max. +200 °C)
6 = high temperature
film insulation
8 = no insulating sleeve
E3 = 100 % tin
termination
(RoHS-compliant
design)
Blank = SnPb
termination
(standard design)
