135D226X9075C6 Datasheet 135D475X9100C6, 135D566X9030C6, 135D337X9050K6 | P7-P9

135D

www.vishay.com

Vishay

Revision: 10-Jun-16

Document Number: 40024

For technical questions, contact: tantalum@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PERFORMANCE CHARACTERISTICS

1. Operating Temperature: capacitors are designed to

operate over a temperature range of -55 °C to +200 °C.

2. DC Working Voltage: the DC working voltage is the

maximum operating voltage for continuous duty at the

rated temperature.

3. Surge Voltage: the surge voltage rating is the maximum

voltage to which the capacitors should be subjected

under any conditions. This includes transients and peak

ripple at the highest line voltage.

3.1 The surge voltage of capacitors is 115 % of rated DC

working voltage.

3.2 Surge Voltage Test: capacitors shall withstand the

surge voltage applied through a 1000  ± 10 % resistor

in series with the capacitor and voltage source at the

rate of one-half minute on, four and one-half minutes

off, for 1000 successive test cycles at +85 °C or

+125 °C.

3.3 Following the surge voltage test, the capacitance at

+25 °C shall not have changed by more than ± 10 % and

the equivalent series resistance and DC leakage current

will not exceed the values shown in the Standard

Ratings table for each capacitor.

4. Capacitance Tolerance: the capacitance of all

capacitors shall be within the specified tolerance limits

of the nominal rating.

4.1 Measurements shall be made by the bridge method at

or referred to a frequency of 120 Hz at a temperature of

+25 °C. The maximum voltage applied to the capacitors

during measurement shall be 1 V

RMS

. Measurement

accuracy of the bridge shall be within ± 2 %.

5. Capacitance Change With Temperature: the

capacitance change with temperature shall not exceed

the values given in the Standard Ratings table for each

capacitor.

6. Equivalent Series Resistance: measurements shall be

made by the bridge method at, or referred to, a

frequency of 120 Hz at a temperature of +25 °C. A

maximum of 1 V

RMS

shall be applied during

measurement.

6.1 The equivalent series resistance shall not exceed the

maximum value in ohms listed in the Standard Ratings

table for each capacitor.

TYPICAL CURVES OF IMPEDANCE AS A FUNCTION OF FREQUENCY AT VARIOUS TEMPERATURES

0.1

1.0

100

100 1K

10K

100K

10M

“C” Case 33 μF, 50 V Capacitors

+ 125 °C

+ 25 °C

- 40 °C

- 55 °C

- 20 °C

+ 85 °C

Frequency (Hz)

Impedance (Ω)

0.1

1.0

100

100 1K

10K

100K

10M

“K” Case 56 μF, 125 V Capacitors

- 55 °C

- 40 °C

- 20 °C

+ 125 °C

+ 25 °C

+ 85 °C

Frequency (Hz)

Impedance (Ω)

UP TO

+85 °C

(V)

+125 °C

(V)

+200 °C

(V)

6 4 3.6

8 5 4.8

10 7 6

15 10 9

25 15 12

30 20 18

35 22 21

40 25 20

50 30 30

60 40 36

63 40 31

75 50 45

100 65 60

125 85 75

135D

www.vishay.com

Vishay

Revision: 10-Jun-16

Document Number: 40024

For technical questions, contact: tantalum@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

6.2 The dissipation factor may be calculated from the

equivalent series resistance and capacitance values as

shown:

where:

DF = dissipation Factor in %

R = ESR in 

C = capacitance in μF

f = frequency in Hz

At 120 Hz, the above equation becomes:



For example, percent dissipation factor of a 30 μF, 6 V

capacitor, which has a maximum ESR of 4.0  at

+25 °C and 120 Hz, would be calculated as shown:

7. Leakage Current: measurements shall be made at the

applicable rated working voltage at +25 °C ± 5 °C

through application of a steady source of power, such

as a regulated power supply. A 1000  resistor to limit

the charging current shall be connected in series with

each capacitor under test. Rated working voltage shall

be applied to capacitors for 5 minutes before making

leakage current measurements.

7.1 The maximum leakage current for any capacitor shall

not exceed the maximum value in microamperes listed

in the Standard Ratings and Extended Ratings table for

each capacitor.

Note

• Leakage current varies with applied voltage. See graph next

column for the appropriate adjustment factor

8. Low Temperature Impedance: the impedance of any

capacitor at -55 °C at 120 Hz, shall not exceed the

values given in the Standard Ratings and Extended

Ratings tables.

9. Life Test: capacitors are capable of withstanding a

2000 h life test at a temperature of +85 °C or +125 °C at

the applicable rated DC working voltage.

9.1 Following the life test, the capacitors shall be returned

to 25 °C ± 5 °C. The leakage current, measured at the

+85 °C rated voltage, shall not be in excess of the

original requirement; the capacitance value shall not

exceed 150 % of the initial requirement; the

capacitance value shall not change more than 10 %

from the initial measurement.

9.3 Capacitors are capable of withstanding life test at the

following conditions:

9.4 Following the life test, the capacitors shall be returned

to +25 °C ± 5 °C. The leakage current, at the rated

voltage shall not exceed 200 % of the original

requirement or ± 10 μA, whichever is greater; the

equivalent series resistance shall not be greater than

200 % of the original requirement; the capacitance

value shall not increase by more than 10 % or decrease

by more than 20 % from the initial measurement.

2fRC

------------------

x C

13.26

---------------

2

x 120 x 4 x 30

----------------------------------------------

4 x 30

13.26

----------------

9.05 %===

TYPICAL LEAKAGE CURRENT FACTOR

RANGE

TEMPERATURE HOURS % RATED VOLTAGE

+175 °C 2000 50

+175 °C 300 65

+200 °C 300 60

0 10 20 30 40 50 60 90 10070 80

1.0

0.9

0.8

0.6

0.5

0.7

0.4

0.3

0.2

0.09

0.08

0.06

0.05

0.07

0.04

0.03

0.02

0.1

0.01

LEAKAGE CURRENT FACTOR

PERCENT OF RATED VOLTAGE

135D

www.vishay.com

Vishay

Revision: 10-Jun-16

Document Number: 40024

For technical questions, contact: tantalum@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

10. Ripple Life Test at +85 °C: capacitors shall be tested

in accordance with Military Specification

MIL-PRF-39006 except that:

a) Operation conditions: this test shall be run at a

frequency of 40 kHz ± 2 kHz sinusoidal and at the

RMS ripple current levels specified in the Standard

Ratings and Extended Ratings table.

b) Applied DC voltage shall be reduced so that the

peak AC voltage plus DC voltage shall not exceed

the rated voltage of the capacitor in either the

forward or reverse direction.

10.1 When tested as specified above, capacitors shall meet

the following requirements:

a) The DC leakage current at +25 °C and at +85 °C

shall not exceed the original requirements.

b) The capacitance shall not change more than ± 15 %

from the initial measured value.

c) The dissipation factor shall not exceed the original

requirements.

d) Visual examination: there shall be no damage,

obliteration of marking or leakage of electrolyte.

11. Reverse Voltage Test: capacitors shall withstand a

reverse voltage of 3 V

at +85 °C or 2 V at +125 °C

for 2000 h. The capacitors shall then be restabilized for

24 h at 85 °C with rated DC forward potential applied

through a 1000  resistor.

11.1 Following the reverse voltage test, the DC leakage

current shall not be in excess of the original

requirement; the equivalent series resistance shall not

exceed 200 % of the initial requirement; the

capacitance value shall not be less than 90 % of the

initial measurement.

12. Mechanical Shock Test: capacitors shall withstand a

shock of 500 g when tested in accordance with

method 213 of MIL-STD-202, test condition D.

12.1 Following the mechanical shock test, capacitors shall

be examined for evidence of mechanical damage and

leakage of electrolyte. Capacitance, equivalent series

resistance, and DC leakage current shall meet the

initial requirements.

13. High Frequency Vibration: capacitors shall withstand

vibration from 10 Hz to 2000 Hz at 80 g without internal

damage when tested in accordance with

MIL-STD-202, method 204, test condition H. Electrical

measurements made while under these conditions

shall show no intermittent contacts, open circuits or

short circuits.

13.1 Capacitors shall be securely fastened by means of

suitable component clips or brackets.

14. Random Vibration: capacitors shall withstand

random vibration at all levels up to 51 g RMS overall

when tested in accordance with MIL-STD-202,

method 214, test condition II K. The test shall be

conducted for 1.5 h in each of three mutually

perpendicular directions.

14.1 Electrical measurements made during the test shall

show no intermittent contacts, open circuits or short

circuits.

15. Pull Test: leads shall withstand a tensile stress of 3

lbs. (1.4 kg) for 30 s applied axially in accordance with

MIL-STD-202, method 211, test condition A.

16. Lead Bend Test: leads shall meet the bend test

specified in Military Standard MIL-STD-202, method

211 A, condition C except that the number of bends

shall be 4.

17. Moisture Resistance: capacitors shall withstand the

moisture resistance cycling test specified in Military

Standard MIL-STD-202, method 106, without

departure from the original limits of capacitance,

equivalent series resistance and DC leakage current.

18. Reduced Pressure: capacitors shall be stabilized at a

reduced atmospheric pressure of 0.82" [20.83 mm] of

mercury for a period of 5 min. Rated DC voltage shall

be applied for 1 min. Capacitors shall not flash over

nor shall end seals be damaged by this nor should the

capacitors be electrically effected insofar as

capacitance, equivalent series resistance or leakage

current is concerned.

19. Seal Test:

19.1 Capacitors shall be tested in accordance with

MIL-STD-202, method 112, test condition C,

procedure IIIa. Specimens shall be pressurized at 4

atmospheres (gage) for 4 h.

20. Thermal Shock: capacitors shall be subjected to 300

cycles of thermal shock in accordance with Military

specification MIL-PRF-39006.

20.1 Following the thermal shock test, capacitor leakage

current shall not exceed twice the initial requirement.

21. Marking: capacitors shall be marked with Vishay

identification; capacitors type (135D); rated

capacitance and tolerance (the tolerance shall be

coded, using the list shown in How to Order); rated DC

working voltage at +85 °C; the standard EIA date

code of manufacture.

21.1 Polarity shall be indicated by plus signs (+) adjacent to

the positive terminal.

P1-P3 P4-P6 P7-P9 P10-P12 P13-P14

135D226X9075C6

Mfr. #:

Buy 135D226X9075C6

Manufacturer:

Vishay

Description:

Tantalum Capacitors - Wet 75volts 22uF 10% C Case EXT RANGE

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

135D226X9075C6

135D226X9075C6

Products related to this Datasheet