SPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
CAPACITIVE LOAD (max.)OUTPUT
LINE REGULATION
LOAD REGULATION
VOLTAGE RANGE
EFFICIENCY (Typ.)
INPUT
WORKING TEMP.
ON/OFF CONTROL
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE(CLAMP)
DC CURRENT
3.3V 5V 5V12V 12V15V 15V3.3V
1.2A 1A 1A0.42A 0.42A0.33A 0.33A1.2A
3.96W
1000uF
0 ~ 1.2A
5W
1000uF
0 ~ 1A
5W
1000uF
0 ~ 1A
5.04W
120uF
0 ~ 0.42A
5.04W
120uF
0 ~ 0.42A
4.95W
120uF
0 ~ 0.33A
4.95W
120uF
0 ~ 0.33A
3.96W
1000uF
0 ~ 1.2A
75mVp-p
±2.0% max.
±1.0%
±2.0%
72%
±1.0%
76%
±1.0%
82%
±1.0%
83%
±2.0%
75%
±1.0%
78%
±1.0%
83%
±1.0%
85%
9.2 ~ 36VDC 18 ~ 72VDC
48VDC
0.7A/12VDC 0.2A/48VDC
5mA/48VDC
Above 105% rated output power
Recovers automatically after fault condition is removed
-25 ~ +70℃
Logic "1" or open circuit : ON Logic "0" or short to PIN2 : OFF
0% ~ 95% RH max.
-40 ~ +85 , 0 ~ 95% RH℃
±℃℃)0.03%/ (0~60
914.4K hrs min. MIL-HDBK-217F (25 )℃
40.6*25.4*8.3mm (1.6"*1"*0.327") (L*W*H)
0.007Kg; 700pcs/5.9Kg/0.97CUFT
1. All parameters NOT specially mentioned are measured at 12, 48VDC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on
a mm* mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.230 230 For guidance on how to
perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)
5. To insure proper operation, a 47uF/100V electrolytic capacitor with Esr <1 must be added to the input line.Ω
6.EMC filter suggestion(TBD):
7. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃
5W DC-DC Regulated Single Output
Wide 4:1 DC input range
Protections: Short circuit / Overload / Over voltage
1000VDC I/O isolation
Cooling by free air convection
Built-in remote ON-OFF control
100% full load burn-in test
Low cost
High reliability
2 years warranty
■
Features :
NSD05-S series
RIPPLE & NOISE (max.) Note.2
VOLTAGE TOLERANCE Note.3
ISOLATION VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:1KVDC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
ENVIRONMENT
PROTECTION
FUNCTION
RATED DC INPUT 12VDC
SHORT CIRCUIT
SHUTDOWN IDLE CURRENT 5mA/12VDC
3.8 ~ 4.6V 3.8 ~ 4.6V5.6 ~ 6.8V 5.6 ~ 6.8V13.5 ~ 16.5V 16.2 ~ 19.8V 13.5 ~ 16.5V 16.2 ~ 19.8V
Protection type : Over power limiting, recovers automatically after fault condition is removed
Compliance to EN55032 (CISPR32) Class B, EAC TP TC 020
Compliance to EN61000-4-2,3,4,5,6,8; EN55024, light industry level, criteria A, EAC TP TC 020
SAFETY &
EMC
(Note 4)
PSU
+
-
Vin
+
-
Vo
5.5uH
680uF
+
NSD05-12S3 NSD05-12S5 NSD05-12S12 NSD05-12S15 NSD05-48S3 NSD05-48S5 NSD05-48S12 NSD05-48S15
SAFETY STANDARDS
IEC60950-1 CB approved by TUV, approvedEAC TP TC 004
EMC IMMUNITY
EMC EMISSION
SETUP TIME
80ms RATED DC INPUT at full Load/
File Name:NSD05-S-SPEC 2018-01-12
