Document Number: 83627 For technical questions, contact: optocoupleranswers@vishay.com
www.vishay.com
Rev. 2.0, 29-Mar-11 1
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Optocoupler, Phototriac Output, Zero Crossing,
High dV/dt, Low Input Current
IL410, IL4108
Vishay Semiconductors
DESCRIPTION
The IL410 and IL4108 consists of a GaAs IRLED optically
coupled to a photosensitive zero crossing TRIAC network.
The TRIAC consists of two inverse parallel connected
monolithic SCRs. These three semiconductors are
assembled in a six pin dual in-line package.
High input sensitivity is achieved by using an emitter
follower phototransistor and a cascaded SCR predriver
resulting in an LED trigger current of less than 2 mA (DC).
The use of a proprietary dV/dt clamp results in a static dV/dt
of greater than 10 kV/ms. This clamp circuit has a MOSFET
that is enhanced when high dV/dt spikes occur between
MT1 and MT2 of the TRIAC. When conducting, the FET
clamps the base of the phototransistor, disabling the first
stage SCR predriver.
The zero cross line voltage detection circuit consists of two
enhancement MOSFETS and a photodiode. The inhibit
voltage of the network is determined by the enhancement
voltage of the N-channel FET. The P-channel FET is enabled
by a photocurrent source that permits the FET to conduct
the main voltage to gate on the N-channel FET. Once the
main voltage can enable the N-channel, it clamps the base
of the phototransistor, disabling the first stage SCR
predriver.
The 600 V, 800 V blocking voltage permits control of off-line
voltages up to 240 V
AC
, with a safety factor of more than
two, and is sufficient for as much as 380 V
AC
.
The IL410, IL4108 isolates low-voltage logic from 120 V
AC
,
240 V
AC
, and 380 V
AC
lines to control resistive, inductive, or
capacitive loads including motors, solenoids, high current
thyristors or TRIAC and relays.
FEATURES
• High input sensitivity
•I
FT
= 2 mA, PF = 1.0
•I
FT
= 5 mA, PF 1.0
• 300 mA on-state current
• Zero voltage crossing detector
• 600 V, 800 V blocking voltage
• High static dV/dt 10 kV/μs
• Very low leakage < 10 A
• Isolation test voltage 5300 V
RMS
• Small 6 pin DIP package
• Compliant to RoHS Directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
APPLICATIONS
• Solid-state relays
• Industrial controls
• Office equipment
• Consumer appliances
AGENCY APPROVALS
• UL1577, file no. E52744 system code H, double protection
• CSA 93751
• DIN EN 60747-5-2 (VDE 0884)/DIN EN 60747-5-5
(pending), available with option 1
Note
(1)
Also available in tubes, do not put T on the end.
i179030_4
1
2
3
6
5
4
MT2
MT1
NC
A
C
NC
*Zero crossing circuit
ZCC*
V
DE
ORDERING INFORMATION
IL410#-X0##T
PART NUMBER PACKAGE OPTION TAPE AND
REEL
AGENCY CERTIFIED/PACKAGE BLOCKING VOLTAGE V
DRM
(V)
UL 600 800
DIP-6 IL410 IL4108
DIP-6, 400 mil, option 6 IL410-X006 IL4108-X006
SMD-6, option 7 IL410-X007T
(1)
IL4108-X007T
(1)
SMD-6, option 8 IL410-X008T -
SMD-6, option 9 IL410-X009T
(1)
IL4108-X009T
(1)
VDE, UL 600 800
DIP-6 IL410-X001 IL4108-X001
DIP-6, 400 mil, option 6 IL410-X016 IL4108-X016
SMD-6, option 7 IL410-X017 IL4108-X017
SMD-6, option 9 IL410-X019T
(1)
-
> 0.1 mm
10.16 mm
> 0.7 mm
7.62 mm
DIP-#
Option 7
Option 6
Option 9
9.27 mm
Option 8